manualshive.com logo in svg

Huawei 3900 Series, Commissioning Manual

Share
Download
Huawei 3900 Series Commissioning Manual Download Page 117

Parameter

Description

OM VLAN ID

VLAN ID of the NodeB configured at the RNC (it must be exported
from the CME if the VLAN is planned)
This parameter can be optionally exported from the CME. It is not
configurable in the 

NodeB Auto Deployment

 window.

OM VLAN Priority

VLAN priority of the NodeB configured at the RNC (it must be
exported from the CME if the VLAN is planned)
This parameter can be optionally exported from the CME. It is not
configurable in the 

NodeB Auto Deployment

 window.

DHCP VLAN ID

Same value as OM VLAN ID (it must be exported from the CME if
the VLAN is planned)
This parameter can be optionally exported from the CME. It is not
configurable in the 

NodeB Auto Deployment

 window.

PING VLAN ID

Same value as OM VLAN ID (it must be exported from the CME if
the VLAN is planned)
This parameter can be optionally exported from the CME. It is not
configurable in the 

NodeB Auto Deployment

 window.

OM PING IP address OM ping IP address

This parameter must be exported from the CME. It is not configurable
in the 

NodeB Auto Deployment

 window.

OM PING IP Subnet
mask

OM ping subnet mask
This parameter must be exported from the CME. It is not configurable
in the 

NodeB Auto Deployment

 window.

NodeB Type

Type of the NodeB to be commissioned
This parameter must be exported from the CME. It is not configurable
in the 

NodeB Auto Deployment

 window.

NodeB BaseLine
Software Version

Baseline version of the target NodeB (it must be exported from the
CME if the target version is planned)
This parameter can be optionally exported from the CME. It is
configurable in the 

NodeB Auto Deployment

 window.

NodeB Cold Patch
Version

Version of the cold patch of the target NodeB (it must be exported
from the CME if the target version is planned)
This parameter can be optionally exported from the CME. It is
configurable in the 

NodeB Auto Deployment

 window.

NodeB Hot Patch
Version

Version of the hot patch of the target NodeB (it must be exported
from the CME if the target version is planned)
This parameter can be optionally exported from the CME. It is
configurable in the 

NodeB Auto Deployment

 window.

NodeB Configuration
File CRC

CRC value of the NodeB data configuration file
This parameter can be optionally exported from the CME. It is not
configurable in the 

NodeB Auto Deployment

 window.

3900 Series Multi-Mode Base Station
Commissioning Guide

5 Commissioning the MBTS in GL or UL Mode on the

M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

5-57

Summary of Contents for 3900 Series





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands