manualshive.com logo in svg

Huawei 3900 Series, Commissioning Manual

Introducing the Huawei 3900 Series - a cutting-edge solution for all your technological needs. This exceptional product offers unparalleled performance and functionality. Enhance your experience with our easy-to-use Solution Manual, available for free download at manualshive.com. Discover the limitless possibilities of the Huawei 3900 Series today!

Share
Download
background image

 

Status of the LED
on the USB Disk

State of the RUN
LED on the
WMPT

Duration

The NodeB resets.

ON first, OFF for a
while, and then
blinking

ON first, OFF for a
while, and then
blinking (ON for
0.125s and OFF for
0.125s)

About 2 minutes

The NodeB runs
normally.

ON

Blinking (on for 1s
and off for 1s)

-

 

NOTE

The time for downloading software and data configuration file from the USB disk and the time for the
NodeB to activate the software may differ from those in 

Table 6-5

, according to the version and

configuration.

----End

6.3.3 Upgrading the eNodeB Software and Downloading the Data
Configuration File (on the eNodeB Side)

This section describes how to download and activate the eNodeB software and data configuration
file through the USB storage device. The eNodeB automatically downloads the software and
data configuration file from the USB storage device, and then activates them. The software and
data configuration take effect after the eNodeB resets.

Prerequisite

The USB storage device is ready for use. The required files are saved in the USB storage device.
For details, see 

6.2.3 Arranging the USB Disk for Local eNodeB Commissioning

.

CAUTION

If one USB storage device is used repeatedly, the target eNodeB software and data configuration
file in the USB storage device should be updated before the USB storage device is used for an
eNodeB deployment.
When you save the eNodeB software and data configuration file to the USB storage device,
ensure that the locking switch on the USB storage device is disabled. In other words, the USB
storage device should be writable.

Context

When the LMPT of the BBU3900 is started, it automatically detects the USB storage device,
reads the related software and data configuration file in the USB storage device, and verifies the
file names and formats.

If you install the BBU before installing the RRU, you can install and power on the RRU during
the process of BBU software downloading. After the BBU software is downloaded and activated

3900 Series Multi-Mode Base Station
Commissioning Guide

6 Commissioning the MBTS by Using USB and M2000

Issue 02 (2010-07-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

6-17

Summary of Contents for 3900 Series





































































































































































































Reviews:

No comments

Related manuals for 3900 Series

CAB PS11 Assembly Instructions Manual preview
PS11
Brand: CAB Pages: 10
Banner MSC 1S Series Supplement Manual preview
MSC 1S Series
Brand: Banner Pages: 12
Baby Brezza One Step BRZ0070 Instructions preview
One Step BRZ0070
Brand: Baby Brezza Pages: 4
Babboe Curve Instruction Manual preview
Curve
Brand: Babboe Pages: 7
Babboe City Instruction Manual preview
City
Brand: Babboe Pages: 7
Hama Multi Operating Instructions Manual preview
Multi
Brand: Hama Pages: 40
Rave Sports SUP User Manual & Owners Manual preview
SUP
Brand: Rave Sports Pages: 16
Parkside PSHL 2 B1 Operation And Safety Notes Translation Of The Original Instructions preview
PSHL 2 B1
Brand: Parkside Pages: 89
Parkside PSH 3 A1 Assembly, Operating And Safety Instructions preview
PSH 3 A1
Brand: Parkside Pages: 28
Waterpik WP-480 User Manual preview
WP-480
Brand: Waterpik Pages: 28
Waterpik WP-600 Series Quick Start Manual preview
WP-600 Series
Brand: Waterpik Pages: 2
Waterpik Water Flosser WF-03 Quick Start Manual preview
Water Flosser WF-03
Brand: Waterpik Pages: 2
Waterpik Models WF-11 Instructions Manual preview
Models WF-11
Brand: Waterpik Pages: 32
Warrior Products 10936 Installation Instructions preview
10936
Brand: Warrior Products Pages: 3
X10 MS12A Set Up And Operating Instructions preview
MS12A
Brand: X10 Pages: 1
Dynojet 1139.005 Quick Start Manual preview
1139.005
Brand: Dynojet Pages: 2
Calex 429198 Getting Started preview
429198
Brand: Calex Pages: 16
Asong POWER FEED Assembly & Operating Instructions preview
POWER FEED
Brand: Asong Pages: 17

Brands by name

Popular brands

Load more brands