Huawei 3900 Series Commissioning Manual Download

Page: 8 / 196

5.2.3 Creating an eNodeB Commissioning Task............................................................................................5-8

5.3 Intervening the GBTS Transmission.............................................................................................................5-13
5.4 Commissioning the MBTS on the M2000....................................................................................................5-17

5.4.1 Procedure for Automatically Commissioning the GBTS by the M2000.............................................5-18
5.4.2 Procedure for Automatically Commissioning the NodeB by the M2000............................................5-22

5.5 Monitoring the GBTS Commissioning Task................................................................................................5-24

5.6 Monitoring the NodeB Commissioning Task...............................................................................................5-28

5.7 Monitoring the eNodeB Commissioning Task..............................................................................................5-32

5.7.1 Viewing the eNodeB Commissioning Progress...................................................................................5-32
5.7.2 Pausing/Retrying the eNodeB Commissioning Task...........................................................................5-34
5.7.3 Restarting/Deleting the eNodeB Commissioning Task.......................................................................5-34

5.8 Obtaining the Commissioning Report...........................................................................................................5-34

5.8.1 Obtaining a GBTS Commissioning Report..........................................................................................5-35
5.8.2 Obtaining a NodeB Commissioning Report.........................................................................................5-36
5.8.3 Obtaining an eNodeB Commissioning Report.....................................................................................5-36

5.9 Checking the Operating Status of the Base Station.......................................................................................5-37

5.9.1 Checking the Running Status of the GBTS..........................................................................................5-37
5.9.2 Checking the Running Status of the NodeB.........................................................................................5-38
5.9.3 Checking the Running Status of the eNodeB.......................................................................................5-38

5.10 Testing the Basic Services of the eNodeB..................................................................................................5-41
5.11 Confirming the Commissioning Task.........................................................................................................5-42

5.11.1 Confirming a GBTS Commissioning Task........................................................................................5-42
5.11.2 Confirming a NodeB Commissioning Task.......................................................................................5-43
5.11.3 Confirming an eNodeB Commissioning Task...................................................................................5-43

5.12 Reference to the GBTS Commissioning Interface......................................................................................5-43

5.13 Reference to the NodeB Commissioning Interface.....................................................................................5-51

5.13.1 Interface Description: NodeB Commissioning..................................................................................5-51
5.13.2 Parameters of the NodeB Deployment List........................................................................................5-54

6 Commissioning the MBTS by Using USB and M2000.......................................................6-1

6.1 Procedure for Commissioning the MBTS by Using USB and M2000...........................................................6-2

Contents

3900 Series Multi-Mode Base Station

Commissioning Guide

Huawei Proprietary and Confidential

Issue 02 (2010-07-30)

Summary of Contents for 3900 Series





































































































































































































Search results

Summary of Contents for 3900 Series

Reviews:

Related manuals for 3900 Series

Brands by name

Popular brands

Huawei 3900 Series, Commissioning Manual

Search results

Summary of Contents for 3900 Series

Reviews:

Related manuals for 3900 Series

Brands by name

Popular brands