manualshive.com logo in svg

HP Kayak XA-s 02xx, User Manual, Page: 91 / 148

Share
Download
HP Kayak XA-s 02xx User Manual Download Page 91

English

79

4   Technical Information

Features

9-pin serial connectors

•

Standard: Two UART 16550 buffered serial ports 
(both RS-232-C).

•

Serial Ports A and B: 2F8h (IRQ 3), 2E8h (IRQ 3), 
3F8h (IRQ 4), 3E8h (IRQ 4), or Off—

(if one port uses 2xxh, the other port must use 3xxh).

Disk drive shelves

Seven mass storage shelves supporting:

•

Two front-access, third-height, 3.5-inch drives

•

Three front-access, half-height, 5.25-inch drives

•

Two internal 3.5-inch hard disk drives

System board connectors

•

One flexible disk drive connector

•

Two ATA/33 IDE connectors (for up to four IDE devices)

•

One CD-ROM audio connector

•

AUX connector

•

Multimedia front panel connector

•

Front panel MIC connector

•

Internal speaker connector

•

One external start connector

•

External battery connector

Accessory slots

•

One AGP (Accelerated Graphics Port) slot

•

Three 32-bit PCI slots

•

One 16-bit ISA (Industry Standard Architecture) slot

•

One combination ISA or PCI slot

Keyboard/Mouse

•

HP enhanced keyboard with mini-DIN connector

•

HP enhanced scrolling mouse with mini-DIN connector

HP UltraFlow cooling system

Cooling system with multiple temperature-regulated fans to 
optimize cooling

Headset

Stereo headset with microphone

Feature:

Description:

geron.bk : geron-4.fb4  Page 79  Sunday, March 22, 1998  5:03 AM

Summary of Contents for Kayak XA-s 02xx





















































































































































Reviews:

No comments