manualshive.com logo in svg

HP Kayak XA-s 02xx, User Manual, Page: 18 / 148

Share
Download
HP Kayak XA-s 02xx User Manual Download Page 18

1   Setting Up and Using Your PC Workstation

Connecting an External SCSI Accessory (Selected Models Only)

6

English

Connecting an External SCSI Accessory
(Selected Models Only)

Your PC Workstation is equipped with an UltraWide 16-bit SCSI 
connector for external SCSI devices. 

When an external SCSI device is connected, the UltraWide 16-bit SCSI 
controller automatically switches to non-Ultra mode (maximum 
capacity of 20 MBs per second).

An external SCSI device is connected as follows:

1

You should assign an unused SCSI address to the accessory. SCSI 
addresses range from 0 to 15 for wide 16-bit SCSI. The SCSI 
address 0 is reserved for the first SCSI hard disk drive and SCSI 
address 7 is reserved for SCSI controller (the default for narrow and 
wide SCSI devices).

Refer to the manual provided with the SCSI accessory for 
instructions on selecting a SCSI address. 

NOTE

You don’t need to set a SCSI address for Plug and Play SCSI devices 
(SCSI devices which support the SCAM protocol).

2

Make sure the SCSI accessory is terminated correctly—either 
internally or by a terminating resistor (refer to the manual provided 
with the SCSI accessory).

Make sure the SCSI 
accessory is terminated

geron.bk : geron-1.fb4  Page 6  Sunday, March 22, 1998  5:03 AM

Summary of Contents for Kayak XA-s 02xx





















































































































































Reviews:

No comments