manualshive.com logo in svg

HP A7533A - Brocade 4Gb SAN Switch Base, Administrator'S Manual

The HP A7533A - Brocade 4Gb SAN Switch Base is a high-performance networking solution essential for seamless data transmission in large-scale storage area networks. Stay up-to-date with the latest features and enhancements by downloading the free Release Note and User Manual from manualshive.com. Experience hassle-free connectivity with this industry-leading product.

Share
Download
background image

Fabric OS 6.2 administrator guide 433

5.

Repeat 

step 4

 for the remote extended ISL port. Both the local and remote extended ISL ports must be 

configured to the same distance level. When the connection is initiated, the fabric will reconfigure.

The following example configures slot 1, port 1 for the LD link distance mode, enables the extended link 

initialization sequence, and sets the desired distance to 50 kilometers:

switch:admin>

 portcfglongdistance 1/1 LD 1 50 

distance_level

One of the following (the numerical value representing each distance_level 

is shown in parentheses):

•

L0 (0) Specify L0 to configure the port to be a regular (default) 

switch port. 

•

LE (3) Specify LE mode for distances up to 10 km. 

•

LD (5) Specify LD for automatic long-distance configuration. The 

buffer credits for the given E_Port are automatically configured, 

based on the actual link distance measured during E_Port 

initialization versus the user-desired distance.

•

LS (6) Specify LS mode to configure a long-distance link with a 

buffer allocation based on a fixed desired distance value.

vc_translation_link_init

Enables the long-distance link initialization sequence. This extended link 

initialization sequence is an enhanced link reset protocol, and avoids 

excessive resetting of ports. 
By default, this option is set to 1 (enabled). It must be set to 1 (enabled) 

when configuring a trunk over extended fabrics. It must be set to 1 for a 

long-distance link not configured for ISL R_RDY mode; otherwise, it must be 

reset to 0.

desired_distance

For an LD-mode link, 

desired_distance

 is a threshold limit for link distance 

to ensure buffer availability for other ports in the same port group. If the 

measured distance exceeds 

desired_distance

, 

desired_distance

 is used; 

otherwise, the measured distance is used.
For an LS-mode link, 

desired_distance

 is used to calculate the buffers 

required for the port.

Summary of Contents for A7533A - Brocade 4Gb SAN Switch Base

































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for A7533A - Brocade 4Gb SAN Switch Base

Baracoda BDRS01 Communication Protocol Manual preview
BDRS01
Brand: Baracoda Pages: 10
Lantronix UDS1100 Programming Manual preview
UDS1100
Brand: Lantronix Pages: 7
Pace DC60Xu Quick Start Manual preview
DC60Xu
Brand: Pace Pages: 14
Evolution EuDTA Quick Start Manual preview
EuDTA
Brand: Evolution Pages: 7
UCONNECT INTERNATIONAL BT-232B User Manual preview
BT-232B
Brand: UCONNECT INTERNATIONAL Pages: 8
Ableconn USB3DP00B User Manual preview
USB3DP00B
Brand: Ableconn Pages: 34
e+p HDMS 31 Instruction Manual preview
HDMS 31
Brand: e+p Pages: 2
GAI-Tronics 190-3170K Installation Manual preview
190-3170K
Brand: GAI-Tronics Pages: 4
Buffalo AirStation WLI-USB-KB11 User Manual preview
AirStation WLI-USB-KB11
Brand: Buffalo Pages: 45
DEMA 68-4 Manual preview
68-4
Brand: DEMA Pages: 3
Curtis Computer AP1075 Instructions preview
AP1075
Brand: Curtis Computer Pages: 2
Honeywell GENT RF-700 Data And Installation preview
GENT RF-700
Brand: Honeywell Pages: 2
Honeywell OneWireless Adapter Installation Manual preview
OneWireless Adapter
Brand: Honeywell Pages: 20
Honeywell DEX-BLE-1 Quick Start Manual preview
DEX-BLE-1
Brand: Honeywell Pages: 2
Honeywell Q7055A Installation Instructions Manual preview
Q7055A
Brand: Honeywell Pages: 54
Honeywell Q7800F Series Manual preview
Q7800F Series
Brand: Honeywell Pages: 2
Honeywell Home C-Wire Adapter Installation Manual preview
Home C-Wire Adapter
Brand: Honeywell Pages: 24
Honeywell BNA-1C Installation Instructions & User Manual preview
BNA-1C
Brand: Honeywell Pages: 54

Brands by name

Popular brands

Load more brands