manualshive.com logo in svg

HP A7533A - Brocade 4Gb SAN Switch Base, Administrator'S Manual

The HP A7533A - Brocade 4Gb SAN Switch Base is a high-performance networking solution essential for seamless data transmission in large-scale storage area networks. Stay up-to-date with the latest features and enhancements by downloading the free Release Note and User Manual from manualshive.com. Experience hassle-free connectivity with this industry-leading product.

Share
Download
background image

486 Configuring and monitoring FCIP extension services

Deleting an FCIP tunnel

1.

Connect to the switch and log in using an account assigned to the admin role.

2.

Enter the 

portCfg fciptunnel

 command to delete FCIP tunnels. The command syntax is as follows.

portcfg fciptunnel [slot/]ge0|ge1 delete tunnel_id

The following example shows two tunnels deleted on slot 8, port ge0:

switch:admin> 

portcfg fciptunnel 8/ge0 delete 6

switch:admin> 

portcfg fciptunnel 8/ge0 delete 7

Deleting an IP interface (IPIF)

The following command deletes an IP interface.

portcfg ipif [slot/]ge0|ge1 delete ipaddr

Deleting an IProute

The following command deletes an IP route for a specified IPv4 address.

portcfg iproute [slot/]ge0|ge1 delete dest_IPv4_addr netmask

For an IPv6 address:

portcfg iproute [slot/]ge0|ge1 delete IPv6_addr/prefix_len

Managing the VLAN tag table

The VLAN tag table is used by ingress processing to filter inbound VLAN tagged frames. If a VLAN tagged 

frame is received from the network and there is no entry in the VLAN tag table for the VLAN ID, the frame 

is discarded. 
The table is used to determine how to tag a frame that is not already tagged. To tag frames destined for a 

specific host address, you must create an entry with an exact matching destination address in the table. 

Only frames destined for that address are tagged with the associated VLAN ID. To tag frames destined for 

a specific network, you must create a destination address entry for the network. For example; if a 

destination address of 192.168.100.0 is specified, all frames destined for the 192.168.100.0 network are 

tagged with the associated VLAN ID, assuming a network mask of 255.255.255.0. If an entry contains a 

destination address of 0.0.0.0, all frames are tagged with the associated VLAN ID. If frames are already 

VLAN tagged, those tags take precedence over entries in this table. 

NOTE:

If you do not specify a destination IP address, the destination address defaults to 0.0.0.0, and all 

frames are tagged with the associated VLAN tag.

FCIP and ipPerf create and maintain entries in the VLAN tag table through their own configuration 

procedures. Manual entries are needed on both the local and remote sides for 

portCmd ping

 and 

portCmd traceroute

 commands when they are used to test and trace routes across a VLAN when no 

FCIP tunnel is active. 

1.

Connect to the switch and log in using an account assigned to the admin role.

2.

Enter the 

portCfg vlantag

 

command to add or delete entries in the VLAN tag table. The syntax for 

the 

portCfg vlantag command

 

is as follows:

portCfg vlantag add|delete ipif_addr vlan_id L2CoS [dst_IP_addr]

where:

ipif_addr

The locally defined IP address.

vlan_id

The VLAN tag used for this tag (range 1-4094).

L2CoS

Layer 2 class of service (range 0-7)

dst_IP_addr

The destination IP address. All frames destined for this IP address will be tagged with the 

specified vlan_id and L2 CoS. If a destination IP address is not specified, all frames not already 

tagged will be tagged. 

Summary of Contents for A7533A - Brocade 4Gb SAN Switch Base

































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for A7533A - Brocade 4Gb SAN Switch Base

IOGear GUF202 User Manual preview
GUF202
Brand: IOGear Pages: 28
Exsys EX-1346 Manual preview
EX-1346
Brand: Exsys Pages: 2
SMC Networks 2870W - annexe 1 Manual preview
2870W - annexe 1
Brand: SMC Networks Pages: 77
H3C ADP040-54V-GL User Manual preview
ADP040-54V-GL
Brand: H3C Pages: 13
Belkin BT-WINXPSP2 (German) Technische Handleiding preview
BT-WINXPSP2
Brand: Belkin Pages: 1
Hama 34385 Quick Manual preview
34385
Brand: Hama Pages: 12
Cellink BTA-6000R User Manual preview
BTA-6000R
Brand: Cellink Pages: 31
Syba SD-EXP50025 User Manual preview
SD-EXP50025
Brand: Syba Pages: 2
IBM Remote Supervisor Adapter User Manual preview
Remote Supervisor Adapter
Brand: IBM Pages: 124
Crux A/V Series Quick Start Manual preview
A/V Series
Brand: Crux Pages: 3
Sony CBK-WA100 Brochure & Specs preview
CBK-WA100
Brand: Sony Pages: 2
Sony BRAVIA KDL-60EX701 Specifications preview
BRAVIA KDL-60EX701
Brand: Sony Pages: 2
Sony BRAVIA KDL-55EX711 Features & Specifications preview
BRAVIA KDL-55EX711
Brand: Sony Pages: 2
Sony BKM-V11 Operating Instructions preview
BKM-V11
Brand: Sony Pages: 2
Sony BKM-V10 Operating Instructions preview
BKM-V10
Brand: Sony Pages: 2
Sony BKM-FW50 Specifications preview
BKM-FW50
Brand: Sony Pages: 2
Sony BKM-FW50 Brochure preview
BKM-FW50
Brand: Sony Pages: 4
Sony BKM-FW31 Specifications preview
BKM-FW31
Brand: Sony Pages: 1

Brands by name

Popular brands

Load more brands