HP 8920A User Manual Download Page 566 | Manualshive

Page: 566 / 658

background image

566

S:\HP892XX\USRGUIDE\manual\connkeys.fb

Chapter 24, Connector, Key, and Knob Descriptions

Connector Descriptions

DC INPUT

This female connector is used with a dc supply to provide power to the
instrument. The male counterpart to this connector is included in the Connector
Kit accessory. (

See "Accessories" on page 589

The following HP parts can also be ordered to assemble the male counterpart to
this connector:

Connector housing: 1251-4782 (1 required)
Connector contacts: 1252-0385 (2 required)

WARNING:

To prevent a potential shock hazard, always connect the chassis ground terminal to earth ground
when operating this instrument from a DC power source.

Digital Test Connections

Control I/O, CW RF OUT, DET OUT, IQ RF IN, 114.3 MHz OUT

The following connectors are only used when an HP cellular adapter (such as an
HP 83203B) is connected to the Test Set to perform digital modulation tests.
These connectors are optional.

1. Control I/O provides control of the cellular adapter.

2. CW RF OUT routes the RF carrier to the cellular adapter. If a cellular adapter is not

present, a jumper must be used to connect this port to the IQ RF IN port.

3. DET OUT routes the average power detector’s signal to the AUX DSP IN of the cellu-

lar adapter for making average power measurements. This port may not be used with
all models of cellular adapter.

4. IQ RF IN routes the RF carrier from the cellular adapter back into the Test Set. If a cel-

lular adapter is not present, a jumper must be used to connect this port to the CW RF
OUT port.

5. 114.3 MHz IF OUT provides the down-converted RF signal to the cellular adapter.

«
...
564
565
566
567
568
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: MacDon Pages: 17

Brand: Olympus Pages: 50

Brand: VAHVA Pages: 19

Brand: Ecco Pages: 3

BELMONT 2001039

Brand: Backyard Discovery Pages: 50

Brand: Backyard Discovery Pages: 45

Brand: Backyard Discovery Pages: 70

Brand: BACtrack Pages: 16

Brand: Dawn Pages: 8

Brand: BACtrack Pages: 13

Brand: Badgematic Pages: 28

Brand: BACtrack Pages: 2

Brand: MADRIX Pages: 28

Brand: BACTcontrol Pages: 28

Brand: Backyard Products Pages: 98

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Brand: Keller Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands