HP 8920A User Manual Download Page 259 | Manualshive

Page: 259 / 658

background image

259

Chapter 7, Configure Screen

Field Descriptions

(Gen)-(Anl)

This field is used with the

RF Offset

field to specify the amount of frequency

offset between the RF Generator and RF Analyzer.

This field is not displayed when the

RF Display

field is set to

Chan

(the offset is

automatically set when using channel tuning).

See Also

"Setting an RF Generator/Analyzer Offset" on page 84

(Gen)-(Anl)
(User Defined)

This field defines the receiver-transmitter frequency offset when using User
Defined channel operation.

Use a positive value when the radio’s receive frequency is higher than the transmit
frequency (such as 45 MHz)

Use a negative value when the radio’s receive frequency is lower than the transmit
frequency (such as

−

45 MHz).

Operating Considerations

The value of this field is only used if the

RF Display

field is set to

Chan

, and the

RF Chan Std

field is set to

USER-DEF

.

See Also

Chan Space (User Defined)

field description, on page 257

RF Chan Std

field description, on page 262

field description, on page 263

Intensity

This field adjusts the screen intensity from a setting of 1 (very dim) to 8 (bright).
If the setting is set too low, the screen can no longer be read. If you can’t read the
screen, and you don’t know where the cursor is (or even what screen is displayed),
press [PRESET], and re-access the CONFIGURE screen. The cursor
automatically goes to this field at that point. Press [8], [ENTER] to set the
maximum intensity, and re-adjust if desired.

This setting is retained when the instrument is turned off.

«
...
257
258
259
260
261
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Hagie Pages: 61

Brand: JackJaw Pages: 2

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: NEC Pages: 54

Brand: parr Pages: 20

Brand: Landoll Pages: 71

Brand: York Fitness Pages: 4

Brand: W&H Pages: 23

Brand: Bartscher Pages: 24

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: dbx Pages: 2

Brand: Eagle Group Pages: 8

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: Hällde Pages: 40

Brand: Hällde Pages: 6

Brand: Ognibene Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands