HP 8920A User Manual Download Page 391 | Manualshive

Page: 391 / 658

background image

391

Chapter 10, Signaling Encoder (AF Generator 2)

Using the EDACS Encoder

Get the Mobile Up on the Control Channel

1. Turn AF Generator 1

Off

(to disable the default 3 kHz FM deviation). To do this, po-

sition the cursor in front of the

3.00

value in the

AFGen1 To

field on the RF GEN-

ERATOR or DUPLEX TEST screen and press the ON/OFF key.

2. Select

ENCODER

from the

To Screen

menu.

3. Select the

Mode

field and choose

EDACS

from the

Choices

menu.

4. Select the standard used by the radio (4800 or 9600 bps).

5. Enter the

Control Channel

settings.

•

The

Number

is the system control channel number programmed into your mobile.

•

The

RX Frequency

is the control channel’s receive frequency for your mobile.

•

The

TX Frequency

is the control channel’s transmit frequency for your mobile.

6. Enter the

Working Channel

settings.

•

The

Number

is the working channel number (programmed into your mobile) that

you want the mobile to be sent to.

•

The

RX Frequency

is the mobile’s receive frequency for the selected working

channel.

•

The

TX Frequency

is the mobile’s transmit frequency for the selected working

channel.

7. Enter the

Logical ID

number.

8. Enter the

Group ID

number.

9. Enter the

Site ID

number.

10. Select the

Send

field (under

RX Test

). The

Status:

field should now indicate

Control

.

11. The Test Set should now be sending the control channel’s site identification informa-

tion to the mobile, and the mobile should indicate that it is receiving the control channel
data.

12. Select the

Handshake

field. This tells the mobile and RF Generator to go to the work-

ing channel frequencies. The mobile should now indicate that it is “busy”, and is tuned
to a working channel (this is a “receiver handshake”). The

Status:

field should now

indicate

Working.

«
...
389
390
391
392
393
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Navman Pages: 17

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: Tascam Pages: 128

Brand: ParaBody Pages: 6

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

Brand: Haag-Streit Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands