HP 8920A User Manual Download Page 4 | Manualshive

Page: 4 / 658

background image

4

Safety
Considerations

GENERAL

This product and related documentation must be reviewed for familiarization with
safety markings and instructions before operation.

This product has been designed and tested in accordance with IEC Publication
1010, "Safety Requirements for Electronic Measuring Apparatus," and has been
supplied in a safe condition. This instruction documentation contains information
and warnings which must be followed by the user to ensure safe operation and to
maintain the product in a safe condition.

SAFETY EARTH GROUND

A uninterruptible safety earth ground must be provided from the main power
source to the product input wiring terminals, power cord, or supplied power cord
set.

CHASSIS GROUND TERMINAL

To prevent a potential shock hazard, always connect the rear-panel chassis ground
terminal to earth ground when operating this instrument from a dc power source.

SAFETY SYMBOLS

Indicates instrument damage can occur if indicated operating limits are exceeded.
Refer to the instructions in this guide.

Indicates hazardous voltages.

Indicates earth (ground) terminal

WARNING

A WARNING note denotes a hazard. It calls attention to a procedure, practice, or
the like, which, if not correctly performed or adhered to, could result in personal
injury. Do not proceed beyond a WARNING sign until the indicated conditions
are fully understood and met.

CAUTION

A CAUTION note denotes a hazard. It calls attention to an operation procedure,
practice, or the like, which, if not correctly performed or adhered to, could result
in damage to or destruction of part or all of the product. Do not proceed beyond
an CAUTION note until the indicated conditions are fully understood and met.

!

«
...
2
3
4
5
6
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Fender Pages: 15

Brand: J D Squared Pages: 18

Brand: Federal Signal Corporation Pages: 12

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

Brand: Tascam Pages: 78

MINISTUDIO CREATOR US-42

Brand: Tascam Pages: 11

Brand: U-Line Pages: 9

Green Machine H-3518

Brand: U-Line Pages: 3

Brand: UEi Pages: 5

Brand: UGO BASILE Pages: 47

Brand: UFO Pages: 16

SimNewB Anomaly Set

Brand: laerdal Pages: 10

Brand: Bodyworx Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands