HP 8920A User Manual Download Page 153 | Manualshive

Page: 153 / 658

background image

153

Chapter 6, Call Processing Subsystem

Using the CALL CONTROL Screen to test AMPS Authentication

Configure the Test Set

1. Select

CALL CNTL

from the

To Screen

menu. The CALL CONTROL screen will

be displayed.

2. Verify that the Test Set configuration information is appropriate for the mobile station

to be tested. Check the following fields:
a.

System Type

- Select AMPS. At this time, only AMPS is supported for authen-

tication.

NOTE:

If the

System Type

field was modified in step 2a- the control channel will become active

since modifying this field automatically activates the control channel. Refer to the

field description, on page 136

b.

Cntl Channel

- Set the control channel number to be used by the Test Set.

NOTE:

If the

Cntl Channel

field was modified in step 2b the control channel will become active

since modifying this field automatically activates the control channel. Refer to the

field description, on page 126

c.

Amplitude

- Set the output power of the Test Sets’s transmitter (that is, the output

power of the Test Set’s RF Generator).

d.

SID

- Enter the system identification number of the Test Set as a decimal number.

e.

Chan:

(right-hand field) - Enter the voice channel number which will be assigned

to the mobile station by the Test Set as either an initial voice channel assignment or
as a handoff voice channel assignment.

f.

Pwr Lvl:

(right-hand field) - Enter the Voice Mobile Attenuation Code (VMAC).

The VMAC determines the mobile station power level to be used on the voice chan-
nel (See

field description, on page 125

for more information about the

voice channel).

g.

SAT:

(right-hand field) - Enter the SAT frequency to be used on the designated

voice-channel (See

field description, on page 125

for more information

about the voice channel).

3. Select

CALL CNFG

under the

To Screen

menu. The CALL CONFIGURATION

screen will be displayed.

4. Verify that the Test Set’s configuration information is appropriate for the mobile station

to be tested. Check the following field:
a.

CMAX

- Set the number of access channels in the system. This will determine how

many channels must be scanned by the mobile station when trying to access the Test
Set. The value of this field will affect the time required for the mobile station to con-
nect with the Test Set.

«
...
151
152
153
154
155
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

Brand: GE Pages: 43

Brand: GE Pages: 37

Brand: GE Pages: 210

Brand: GE Pages: 160

Brand: GE Pages: 146

Brand: GE Pages: 6

Brand: GE Pages: 27

Brand: GE Pages: 4

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: Raymarine Pages: 90

Brand: B&G Pages: 3

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Haki Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands