HP 8920A User Manual Download Page 240 | Manualshive

Page: 240 / 658

background image

240

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Using the CALL BIT Screen

System Operation When Data Spec Field Set to Std

When the

Data Spec

field is set to

Std

the Test Set builds the signaling

messages by first examining the fields which contain the information needed to
build the messages (i.e. SID, BIS, SAT Tone, VMAC, etc.). After obtaining the
necessary information the Test Set builds the bit patterns according to the
signaling formats specified in the applicable industry standard.

For example: if the type of cellular system being emulated is AMPS and the

SID

field on the CALL PROC screen was set to 231, the SID1 field in the System
Parameter Overhead Message (SPC WORD1) would be set to 00000001110011
(the 14 most significant bits of the system identification number) as defined by the
EIA/TIA-553 Mobile Station - Land Station Compatibility Specification.

When the

Data Spec

field is set to

Std

, the contents of the applicable

message(s) on the CALL BIT screen are updated with the bit patterns generated
using the signaling formats defined in the applicable industry standard whenever
that signaling message is sent to the mobile station. This feature allows a user to
set the

Data Spec

field to

Std

, select a message of interest, perform a call

processing function, and view the bit patterns generated using the signaling
formats defined in the applicable industry standard.

It is important to note individual messages can be used more than once during a
messaging protocol. The contents of any message viewed on the CALL BIT
screen when the

Data Spec

field is set to

Std

will reflect the message contents

for the last time the message was used in a messaging protocol.

For example: if the Call Processing Subsystem is in the active state and the user
selects the

Register

field, a registration message will be sent to the mobile

station. When the registration completes the Call Processing Subsystem returns to
the active state. The contents of some messages (such as the System Parameter
Overhead Message Word 1) will reflect the correct settings for the active state, not
the register state, since the messages are currently being used in the active state.

«
...
238
239
240
241
242
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: NARGESA Pages: 50

Brand: Jacobs Ladder Pages: 16

Brand: ADVANCED HOME CARE Pages: 16

Brand: Fellowes Pages: 20

Brand: P.Lindberg Pages: 76

Brand: Sabo Pages: 76

Brand: Rigol Pages: 12

Brand: Jenx Pages: 34

Brand: B+S Pages: 16

Brand: Petromax Pages: 16

Brand: SereneLife Pages: 4

Brand: Eagle Play Sets Pages: 3

Brand: K-SPORT Pages: 5

Brand: Brillion Pages: 56

Brand: Etesia Pages: 28

Brand: Life Pages: 2

Brand: Vari Lite Pages: 6

Brand: OCEM Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands