HP 8920A User Manual Download Page 166 | Manualshive

Page: 166 / 658

background image

166

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

CALL DATA Screen

RVCOrdCon

- Reverse Voice Channel Order Confirmation Message

•

Reverse Control Channel Authentication Messages.

BSChalOrd

- Word C - Base Station Challenge Word

AuthWORD

- Word C - Authentication Word

UniqChCon

- Word C - Unique Challenge Order Confirmation Word

•

Reverse Voice Channel Authentication Messages.

RVCOrd

- Word one - Reverse Voice Channel Generic Order

RVCBSChal

- Word 2 - Reverse Voice Channel Base Station Challenge Order

•

NAMPS Reverse Voice Channel Messages.

NRVC Ord

- Narrow Order or Order Confirmation Message

The field descriptions for each of the decoded messages are given in the

DATA Screen Message Field Descriptions" on page 170

When the CALL DATA screen is displayed and the Call Processing Subsystem is
in the connected state, the Test Set constantly monitors the mobile station’s
transmitted carrier power. If the power falls below 0.0005Watts, the error
message

RF Power Loss indicates loss of Voice Channel

will be

displayed and the Test Set will terminate the call and return to the active state.

NOTE:

In order to ensure that the Test Set makes the correct decisions regarding the presence of the
mobile stations’s RF carrier, the Test Set’s RF power meter should be zeroed before using the
Call Processing Subsystem. Failure to zero the power meter can result in erroneous RF power
measurements. See

"Conditioning the Test Set for Call Processing" on page 141

information on zeroing the RF Power meter manually.

[] Access

When lit, the

Access

annunciator indicates the Test Set is signaling the mobile

station with command information on the forward voice channel. This is a
transitory state.

The Test Set’s speaker is turned off when in the access state. This is done to
eliminate any possible audio feedback which may occur if the mobile station’s
microphone is open.

«
...
164
165
166
167
168
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: ZIGBEE Pages: 6

Brand: Daisy Pages: 2

Below Ground Pool Cover Box

Brand: Daisy Pages: 3

Brand: iFIT Pages: 11

Brand: Mackie Pages: 18

Brand: Mackie Pages: 2

Brand: Mackie Pages: 8

Brand: Mackie Pages: 7

Brand: Qlight Pages: 4

Brand: Abus Pages: 12

Littmann Classic II Pediatric

Brand: 3M Pages: 53

FUSION Equine DR II

Brand: SOUND Pages: 178

Brand: Jumper Pages: 12

Brand: SMC Networks Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands