HP 8920A User Manual Download Page 154 | Manualshive

Page: 154 / 658

background image

154

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Using the CALL CONTROL Screen to test AMPS Authentication

Turn on the Test Set’s Control Channel

1. If not already done, condition the Test Set.

See "Condition the Test Set for Call Pro-

cessing" on page 152

for further information.

2. If not already done, configure the Test Set.

See "Configure the Test Set" on page 153

for further information.

3. If the CALL CONTROL screen is not displayed, select

CALL CNTL

from the

To

Screen

menu. The CALL CONTROL screen will be displayed.

4. Select

Active

field. The

Active

annunciator will light when the control channel is

turned on.

Initialize Call Processing with Authentication

There are two methods to initialize Call Processing with authentication.

•

Initializing Call Processing with Authentication through registration with the Test Set.

•

Initializing Call Processing with Authentication without registration with the Test Set.

Initialize Call Processing through Registration
1. Ensure that the Test Set is in the active state.

See "Turn on the Test Set’s Control

Channel" on page 154

for information on how to activate the Test Set.

2. Connect the mobile station to the Test Set as shown in

Figure 17, "Connecting a

Mobile Station to the Test Set," on page 119

.

3. Turn on the mobile station.
4. If the CALL CONTROL screen is not displayed, select

CALL CNTL

under the

To

Screen

menu. The CALL CONTROL screen will be displayed.

5. Position the cursor on the

Display

field and select

Data

.

6. Select the

Register

field. The

Register

annunciator will light while the

registration is in process. If the mobile station responds properly on the reverse control
channel, the message

RECC Return

will flash momentarily in the upper right-hand

corner of the CALL CONTROL screen and then the mobile station’s phone number,
ESN and decoded SCM will be displayed in the upper right-hand portion of the CALL
CONTROL screen. The information in the

MS Id

field will be updated. The

Active

annunciator will light when the registration has successfully completed.

7. Select

AUTHEN

on the To Screen field. The AUTHENTICATION screen will be

displayed.

8. Select the

A_KEY

field and enter a valid A_KEY in decimal format.

9. Position the cursor on the

Off/On

field and select

On

.

10. Select

CALL CNTL

from the

To Screen

menu. The CALL CONTROL screen will

be displayed.

«
...
152
153
154
155
156
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Hanil Pages: 60

Brand: NEC Pages: 54

Brand: Panasonic Pages: 30

Brand: Olsen Pages: 56

Brand: Waterous Pages: 5

Brand: 3TECH Pages: 32

Brand: 4EVAC Pages: 15

Brand: Cambro Pages: 6

Brand: Omlet Pages: 60

Brand: PAS Systems International Pages: 24

MARK V Alcovisor

Brand: PAS Systems International Pages: 20

Brand: PARRY Pages: 14

Brand: York Fitness Pages: 36

Brand: Raytec Pages: 60

Brand: RBC Bioscience Pages: 24

Brand: S&C Pages: 16

Brand: S&C Pages: 23

Brand: Cannon Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands