HP 8920A User Manual Download Page 243 | Manualshive

Page: 243 / 658

background image

243

Chapter 6, Call Processing Subsystem

Using the CALL BIT Screen

Typical Example

The following example illustrates the use of the CALL BIT screen. In this
example an AMPS mobile station is brought up on a voice channel and then
handed off to a new voice channel assignment. The contents of the

FVC V Msg

message, which was set when the first handoff occurred, is then modified from the
CALL BIT screen. The mobile station is then handed off again by sending the
modified message to the mobile station from the CALL BIT screen.

1. Ensure that the Test Set is in the connected state.

See "Page a Mobile Station" on

for information on how to bring a mobile station up on a voice channel.

2. If the CALL CONTROL screen is not displayed, select

CALL CNTL

under the

To

Screen

menu. The CALL CONTROL screen will be displayed.

3. Position the cursor on the

Display

field and select

Data

.

4. Select the

Chan:

field and enter a new, valid voice channel number.

5. Select the

Pwr Lvl:

field enter a new, valid mobile station power level.

6. Select the

SAT:

field and enter a new, valid SAT frequency.

7. Select the

Handoff

field. The

Access

annunciator will light while the Test Set

signals the mobile station with the handoff information. If the mobile responds
properly, it will stop transmitting on the current voice channel, switch to the new voice
channel assignment, and transpond the new SAT frequency assignment. When the Test
Set detects that this has happened the

Connect

annunciator is lit indicating that the

handoff was successful. The left-hand fields in the

Voice Channel Assignment

section will be updated with the new voice channel assignment information.

8. Select

CALL BIT

from the

To Screen

menu. The CALL BIT screen will be

displayed.

9. Position the cursor on the

Data Spec

field and select

Bits

.

10. Select the

Set Message

field and select

FVC V Msg

.

11. Select the

VMAC

field in the

FVC V Msg

and set it to 101 (this corresponds to a mobile

station power level of 5 - reference EIA/TIA-553 Mobile Station - Land Station
Compatibility Specification, September 1989, page 2-2, Table 2.1.2-1).

12. Select the

Handoff

field. The

Access

annunciator will light while the Test Set

signals the mobile station with the handoff information. If the mobile responds
properly, it will stop transmitting on the current voice channel, and start transmitting on
the same channel with a power level of 5 (note that the channel assignment and SAT
assignment were not modified in this example, the mobile station simply switched to
the same channel with the same SAT assignment). When the Test Set detects that this
has happened, the

Connect

annunciator is lit indicating that the handoff was

successful. The mobile station power level after the handoff should be power level 5.

13. Position the cursor on the

Data Spec

field and select

Std

.

«
...
241
242
243
244
245
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Raymarine Pages: 90

Brand: CAMAG Pages: 40

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

Brand: Qlight Pages: 4

Brand: Saadat Pages: 61

Brand: Saadat Pages: 22

Brand: Task Force Tips Pages: 16

i-limb access hand

Brand: Össur Pages: 246

PROPRIO FOOT PSX01

Brand: Össur Pages: 374

Brand: Salter Pages: 18

Brand: Salter Pages: 42

Brand: Salter Pages: 47

Brand: Salter Pages: 35

Brand: Salter Pages: 40

M-041 INDOOR CROSS

Brand: Salter Pages: 15

Brand: Strapack Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands