HP 8920A User Manual Download Page 536 | Manualshive

Page: 536 / 658

background image

536

S:\HP892XX\USRGUIDE\manual\testscrn.fb

Chapter 22, Tests Screen

TESTS (Execution Conditions)

Autostart Test Procedure on Power-Up

When set to

On

, this field automatically loads and runs the specified procedure

whenever the Test Set is turned on. If this field is set to

Off

or the specified

procedure cannot be loaded for any reason (such as, memory card not inserted,
disk drive not connected), the Test Set will default to its normal power-on state.

Continue

This field is used to restart a paused test.

If Unit-Under-Test Fails

This field selects what happens if the measured results do not meet criteria for
passing the current test. The underlined entry is the active choice.

•

Continue

continues with testing even though a test in the test sequence fails to meet

its test specification limits. When this occurs, an error is listed on the test-results print-
out, is displayed on the CRT, or both.

•

Stop

stops the test when a failure occurs and requires operator intervention before test-

ing proceeds.

Main Menu

Selecting this field returns you to the TESTS (Main Menu) screen.

Output Heading

This field allow you to enter a heading for the test results printout (or CRT
display).

Output Results To

This field selects where test results are output. The underlined entry is the active
choice.

•

CRT

displays test results on the Test Set’s CRT.

•

Printer

displays test results on the Test Set’s CRT and outputs them to a printer.

(The printer information must first be entered on the TESTS (Printer Setup) screen.)

«
...
534
535
536
537
538
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: ZOLL Pages: 84

Brand: Kaivac Pages: 29

Brand: MacDon Pages: 65

Brand: Palazzetti Pages: 112

Brand: Bahco Pages: 9

Brand: Panlux Pages: 2

Brand: XanLite Pages: 4

Brand: Nitecore Pages: 4

Brand: laerdal Pages: 9

Brand: Major tech Pages: 12

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: GE Pages: 18

Brand: ABB Pages: 4

Brand: Interacoustics Pages: 25

Brand: Hamilton Beach Commercial Pages: 32

BOMAG BW 120 AD-5

Brand: Fayat Pages: 210

Levitator III F-LHLEV3

Brand: Skytron Pages: 248

Brand: Viavi Pages: 404

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands