HP 8920A User Manual Download Page 195 | Manualshive

Page: 195 / 658

background image

195

Chapter 6, Call Processing Subsystem

CALL BIT Screen

The CALL BIT screen should not be used to change any parameter that can be set
on any other Call Processing Subsystem screen. The contents of the applicable
fields on the CALL CONTROL screen and the CALL CONFIGURE screen are
not updated to reflect any changes made while using the CALL BIT screen. There
is no coupling between the CALL BIT screen and the Test Set.

For example: changing the value of the SAT color code field (SCC) in the forward
control channel mobile station control message (MS IntVCh) does not change the
setting of the

SAT:

field on the CALL CONTROL screen.

When using the CALL BIT screen the user is responsible for setting the contents
of all messages used in a messaging protocol. When using the CALL BIT screen,
the Call Processing Subsystem sends the correct messages at the correct times as
defined in the applicable industry standard. Message content is the responsibility
of the user.

When the CALL BIT screen is displayed and the Call Processing Subsystem is in
the connected state, the Test Set constantly monitors the station’s transmitted
carrier power. If the Power falls below 0.0005 Watts, the error message

RF

Power Loss indicates loss of Voice Channel

will be displayed and the

Test Set will terminate the call and return to the active state.

NOTE:

In order to ensure that the Test Set makes the correct decisions regarding the presence of the
mobile stations’s RF carrier, the Test Set’s RF power meter should be zeroed before using the
Call Processing Subsystem. Failure to zero the power meter can result in erroneous RF power
measurements. See

"Conditioning the Test Set for Call Processing" on page 141

information on manually zeroing the RF Power meter.

The field descriptions for each of the messages are given in the

Screen Message Field Descriptions" on page 201

«
...
193
194
195
196
197
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Hagie Pages: 61

Brand: JackJaw Pages: 2

Brand: Parker Pages: 54

Brand: GE Pages: 698

Brand: Raytech Pages: 21

Brand: Teac Pages: 2

Brand: laerdal Pages: 2

Brand: M-system Pages: 2

Brand: Rico Pages: 34

Brand: Qiagen Pages: 48

Brand: Qiagen Pages: 162

Brand: Qazqa Pages: 4

Brand: Qlightec Pages: 12

Brand: Saadat Pages: 61

Brand: Saadat Pages: 22

Brand: Velleman Pages: 16

Brand: Velleman Pages: 11

Brand: Agilent Technologies Pages: 114

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands