HP 8920A User Manual Download Page 136 | Manualshive

Page: 136 / 658

background image

136

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

The CALL CONTROL Screen

SAT:

SAT:

is divided into two fields:

he left-hand field displays the SAT frequency assigned to the voice channel being used by
the Test Set and the mobile station. A numeric value would only be displayed when the
Test Set’s

Connected

annunciator is lit (connected state). A “-” is displayed if a mobile

station is not actively connected on a voice channel.

The right-hand field (highlighted field) is used to set the SAT Color Code (SCC) to be
used on the designated voice channel (

field description, on page 125

for more

information about the voice channel).

SCM:

This field displays the decoded station class mark information received from the
mobile station on the reverse control channel in response to a forward control
channel message. The

SCM:

field is displayed only when the

Display

field is set

to

Data

and a reverse control channel message has been decoded.

SID

This field is used to set the system identification number (SID) of the Test Set.
The

SID

field is an immediate action field. If the field is selected and changed, the

signaling message(s) being sent on the forward control channel are immediately
changed. No change occurs to the current state (that is, active, register, page,
access, connect) of the Call Processing Subsystem.

System Type

This field is used to select the type of cellular system (AMPS, NAMPS, TACS,
JTACS) which will be simulated.

The

System Type

field is an immediate action field. That is, whenever the

System Type

field is changed, the change is reflected immediately in the

physical configuration of the Test Set. The control channel is immediately de-
activated, reconfigured, and then re-activated to reflect the change. This change
causes the Test Set to enter the active state).

If the Test Set is in the connected state (

Connect

annunciator is lit) and a change is made

to the

System Type

field, the connected state will be lost.

«
...
134
135
136
137
138
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: ABB Pages: 14

Brand: BANLAW Pages: 32

Brand: Baker Instrument Company Pages: 24

Brand: NORLUX Pages: 2

Brand: Garmin Pages: 20

9NP-B7524 Series

Brand: Nautilus Pages: 2

Be strong NS 700X

Brand: Nautilus Pages: 34

Brand: Nautilus Pages: 21

Brand: R&S Pages: 371

Brand: R.M. Young Pages: 9

Brand: TDR Pages: 8

Brand: Garmin Pages: 2

Brand: Parker Pages: 58

Brand: +GF+ Pages: 2

Unity for Pro-Flex Pivot

Brand: Össur Pages: 40

ICELOCK 234 LANYARD

Brand: Össur Pages: 94

Brand: Össur Pages: 115

Brand: Össur Pages: 253

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands