HP 8920A User Manual Download Page 189 | Manualshive

Page: 189 / 658

background image

189

Chapter 6, Call Processing Subsystem

Using the CALL DATA Screen

NOTE:

If a word is chosen which was not part of the decoded reverse channel’s message stream, all
the fields will be blank when it is displayed.

See "CALL DATA Screen Message Field Descriptions" on page 170

for a

description of each of the available reverse channel words.

Step 9. and step 11. in the above procedure can be reversed, that is - the desired
word can be selected first, then the mobile station can be paged. If the page is
successful, the contents of each display word contained in the reverse control
channel’s message stream will be updated when the decoding is complete.

The page does not have to happen while you are viewing the CALL DATA
screen. When the CALL DATA screen is viewed, the contents of the display
words will be the decoded data from the last successful call processing function
(registration, origination, page, release, order).

To View the Decoded Reverse Channel Words From a Mobile Station Handoff

1. If not already done, condition the Test Set.

See "Conditioning the Test Set for Call

Processing" on page 141

for further information.

2. If not already done, configure the Test Set.

See "Configure the Test Set" on page 142

for further information.

3. Connect the mobile station to the Test Set as shown in

Figure 17, "Connecting a

Mobile Station to the Test Set," on page 119

.

4. Turn on the mobile station.
5. Ensure that the Test Set is in the

Connect

state.

See "Page a Mobile Station" on

for information on how to bring a mobile station up on a voice channel.

6. If the CALL CONTROL screen is not displayed, Select

CALL CNTL

from the

To

Screen

menu. The CALL CONTROL screen will be displayed.

7. Select the

Chan:

field and enter a new, valid voice channel number from the choices

provided.

8. Select the

Ch Loc:

field (

NAMPS System Type

only) and enter a new, valid

channel location from the choices provided.

Select the

Pwr Lvl:

field and enter a new, valid mobile station power level.

9. Select the

DSAT:

field (

NAMPS System Type

only) and enter a new, valid DSAT

from the choices menu.

Select the

SAT:

field and enter a new, valid SAT frequency.

10. Select

CALL DATA

from the

To Screen

menu. The CALL DATA screen will be

displayed.

«
...
187
188
189
190
191
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: zipwake Pages: 2

Brand: zipwake Pages: 2

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: KaVo Pages: 13

Brand: vc999 Pages: 52

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: Facnor Pages: 33

Brand: Danfoss Pages: 106

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: Federal Signal Corporation Pages: 4

Brand: FEBER Pages: 2

Brand: FASTERHOLT Pages: 96

Brand: Labnet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands