HP 8920A User Manual Download Page 141 | Manualshive

Page: 141 / 658

background image

141

Chapter 6, Call Processing Subsystem

Using the CALL CONTROL Screen to Test Call Processing Functions

Conditioning the Test Set for Call Processing

Perform the following steps when first entering the Call Processing Subsystem
(that is, the first time the CALL CONTROL screen is selected during a
measurement session).

1. Zero the RF Power Meter.

Select the

RF GEN

from the

To Screen

menu.

a. Set the

Amplitude

field to off (use the ON/OFF key). This prevent cross-cou-

pling into the power detector while zeroing the power meter.

b. Select

CALL CNTL

from the

To Screen

menu.

c. Select

CALL CNFG

from the

To Screen

menu.

d. Disconnect any cables from the RF IN/OUT port on the front panel of the Test Set.
e. Select the

TX Pwr Zero

field.

f.

Select the

RF Gen

from the To Screen menu.

g. Set the

Amplitude

field to On.

There are two reasons for zeroing the RF power meter:

•

When any Call Processing Subsystem screen is displayed (except the ANALOG
MEAS screen) and the Call Processing Subsystem is in the connected state (

Con-

nect

annunciator is lit), the Test Set constantly monitors the mobile station’s trans-

mitted carrier power. If the power falls below 0.0005 Watts, the error message

RF

Power Loss indicates loss of Voice Channel

will be displayed

and the Test Set will terminate the call and return to the active state. Zeroing the
power meter cancels any inherent dc offsets that may be present within the power
meter under zero-power conditions. This ensures that the Test Set makes the correct
decisions regarding the presence of the mobile stations’s RF carrier.

•

Zeroing the power meter establishes a 0.0000 W reference for measuring the mobile
station’s RF power at the RF IN/OUT port. This ensures the most accurate RF pow-
er measurements of the mobile station’s RF carrier at different power levels.

«
...
139
140
141
142
143
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Parker Research Corp Pages: 3

Brand: S.I.T.A. Pages: 32

Brand: Raymarine Pages: 55

Brand: Halyard Pages: 4

Underwater Light Show & Fountain

Brand: GAME Pages: 2

Brand: SAMCHULLY Pages: 48

Brand: Gallagher Pages: 6

Brand: Ultraflex Pages: 3

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Brand: Parkside Pages: 58

Brand: PAS Systems International Pages: 24

MARK V Alcovisor

Brand: PAS Systems International Pages: 20

Brand: PARRY Pages: 14

Brand: York Fitness Pages: 36

Brand: ABB Pages: 4

MIAMI J ADVANCED

Brand: Össur Pages: 35

Brand: Össur Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands