HP 8920A User Manual Download Page 117 | Manualshive

Page: 117 / 658

background image

117

Chapter 6, Call Processing Subsystem

Description of the Call Processing Subsystem

Accessing the Call Processing Subsystem’s Screens

The Call Processing Subsystem screens are accessed by selecting

CALL CNTL

from the

To Screen

menu on the Test Set’s CRT (you may have to choose the

More

choice to display the

CALL CNTL

choice).

Option 004:Tone/Digital Signalling is required in an HP 8920A in order to use the Call
Processing Subsystem. Attempting to access the Call Processing Subsystem without
Option 004 installed will generate an “Option not installed.” error.

Call Processing Subsystem’s Screens

The Call Processing Subsystem consists of six screens.

five

•

The CALL CONTROL is the primary Call Processing Subsystem screen. This screen
contains the fields used to configure the Test Set’s parameters such as SAT Tone fre-
quency, control channel number, and system identification number. Call processing
functions such as registration, page, and handoff can be activated from this screen. The
transmit power of the mobile station can be set from this screen. Data messages re-
ceived from the mobile station are displayed on this screen.

•

The CALL DATA screen displays the decoded signaling messages received from the
mobile station on the reverse control channel and the reverse voice channel. Call pro-
cessing functions such as registration, page, and handoff can also be activated from this
screen. The transmit power of the mobile station can be set from this screen.

•

The CALL BIT screen allows the advanced user to modify the contents of the forward
control channel and forward voice channel messages.

•

The CALL CONFIGURE screen contains the fields used to configure various parame-
ters related to the Call Processing Subsystem, such as

CMAX

,

Detector

, and

Input

Att

.

The ANALOG MEAS screen is used to make analog RF and audio measurements on the
mobile station while a link is active.

AUTHENTICATION screen allows the user to turn on the AMPS authentication process
(IS-54) during call processing functions. Various fields contained on this screen allow the
advanced user to select new

RAND_A

,

RAND_B

,

RandSSD

and

RAND_U

values for trans-

mission to the mobile station. The user can also select the number of times the system
parameter overhead message is sent to the mobile station.

AMPS

Call Processing functions

can be tested with or without authentication active.

Call Processing functions with Authentication are only supported for AMPS system types
(IS-54).

«
...
115
116
117
118
119
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Campden instruments Pages: 8

Brand: Canta Pages: 2

Brand: Yamaha Pages: 78

Brand: Fast Pages: 42

Brand: DARAY Pages: 28

Brand: Backyard Play Systems Pages: 64

Brand: Haenim Pages: 2

Brand: MacDon Pages: 272

Brand: MacDon Pages: 70

Brand: FJC Pages: 2

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: Hagerman Pages: 4

Brand: hager Pages: 2

TECSHOW QUAD SPIDER 60

Brand: Ampro Pages: 9

Brand: lancer Pages: 3

Brand: lancer Pages: 12

Brand: R2 Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands