HP 8920A User Manual Download Page 192 | Manualshive

Page: 192 / 658

background image

192

S:\HP892XX\USRGUIDE\manual\callscrn.fb

Chapter 6, Call Processing Subsystem

Using the CALL DATA Screen

To View the Decoded Reverse Channel Words from an Order to Change the Transmit Power
Level of a Mobile Station

1. If not already done, condition the Test Set.

See "Conditioning the Test Set for Call

Processing" on page 141

for further information.

2. If not already done, configure the Test Set.

See "Configure the Test Set" on page 142

for further information.

3. Connect the mobile station to the Test Set as shown in

Figure 17, "Connecting a

Mobile Station to the Test Set," on page 119

.

4. Turn on the mobile station.
5. Ensure that the Test Set is in the

Connect

state.

See "Page a Mobile Station" on

for information on how to bring a mobile station up on a voice channel.

6. If the CALL DATA screen is not displayed, select

CALL DATA

under the

To Screen

menu. The CALL DATA screen will be displayed.

7. Select the

Order

field and select it. A

Choices:

menu is displayed showing the

various power levels which the mobile station can be set to. Select the desired power
level. The

Access

annunciator will light while the Test Set signals the mobile station

with an order to set its power level. If the mobile responds properly, the message

REVC

Return

will flash momentarily in the upper right-hand corner of the CALL

CONTROL screen. The

Connect

annunciator will light when signaling is complete.

8. Select the

Display Word

field. A list of reverse channel words which can be

displayed will be presented. Position the cursor on the desired word and select it. The
decoded contents for each of the fields in the selected word will be displayed in the
lower portion of the display.

9. If a word is chosen which was not part of the decoded reverse channel’s message

stream, all the fields will be blank when it is displayed.

10.

See "CALL DATA Screen Message Field Descriptions" on page 170

for a

description of each of the available reverse channel words.

Step 7. and Step 8. in the above procedure can be reversed, that is, the desired
word can be selected first, then the mobile station can be sent an order to change
transmit power level. If the order is successful, the contents of each display word
contained in the reverse control channel’s message stream will be updated when
the decoding is complete.

The ordered to change transmit power does not have to happen while you are
viewing the CALL CONTROL screen. When the CALL DATA screen is viewed,
the contents of the display words will be the decoded data from the last successful
call processing function (registration, origination, page, release, order).

«
...
190
191
192
193
194
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: JB-Lighting Pages: 40

Brand: Backyard Play Systems Pages: 74

Brand: Federal Signal Corporation Pages: 4

Brand: ParaBody Pages: 7

Brand: Nitecore Pages: 4

Brand: Harken Pages: 4

Brand: Harken Pages: 2

TERRA FORCE BOOM

Brand: Hardi Pages: 40

Brand: Harken Pages: 4

QuickSlide HemaPRO

Brand: Hardy Diagnostics Pages: 2

Brand: Hardt Pages: 2

Brand: Pari Pages: 50

Brand: Icare Pages: 42

Brand: Valko Pages: 10

Brand: MadLab Pages: 7

Brand: Milestone Pages: 64

Brand: Bavis Pages: 8

Brand: Qtx Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands