HP 8920A User Manual Download Page 245 | Manualshive

Page: 245 / 658

background image

245

Chapter 6, Call Processing Subsystem

ANALOG MEAS Screen

AF Freq

This field is a one-of-many field used to select the type of measurement to be
made by the Audio Frequency Analyzer on the audio signal being measured.
Refer to the

field description, on page 110

for descriptions of the

measurements available.

AFGen1 Freq

This field sets the output frequency of Audio Frequency Generator 1. Refer to the

AFGen1 Freq

field description, on page 486

for further information.

AFGen1 To

This field has two fields:

•

the upper field sets the destination port for Audio Frequency Generator 1
•

FM

-RF Generator FM modulator

•

AM

-RF Generator AM modulator

•

Audio Out

-AUDIO OUT connector on front panel of Test Set

•

the lower field sets the:
•

FM modulation deviation if the upper field set to

FM

•

AM modulation depth if the upper field set to

AM

•

amplitude of audio signal (volts RMS) at the AUDIO OUT connector if upper field
is set to

Audio Out

For testing mobile stations, the upper field is normally set to

FM,

and the lower

field set to the desired FM deviation in kHz. Refer to the

AFGen1 Freq

description, on page 486

for further information.

Amplitude

This field sets the output power of the Test Sets’s transmitter (that is, the output
power of the Test Set’s RF Generator). Refer to the

field description,

on page 487

for further information.

De-Emphasis

This field is used to select or bypass the 750

µ

s de-emphasis filter network used to

condition the audio signal before being analyzed by the Audio Frequency
Analyzer. Refer to the

De-Emphasis

field description, on page 104

for further

information.

«
...
243
244
245
246
247
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Makerfire Pages: 10

Brand: Harken Pages: 4

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: Xiitech Pages: 6

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: Lumineux Pages: 2

Brand: PHAROS MARINE Pages: 17

Aesculap S4 Cervical

Brand: B. Braun Pages: 43

Dynamique Biski

Brand: Enabling Technologies Pages: 44

Brand: ASIA TECHNOLOGY Pages: 38

TRAKTOR KONTROL S3

Brand: Native Instruments Pages: 39

Brand: K-SPORT Pages: 4

Brand: Baldan Pages: 72

Brand: Avicenum Pages: 32

Brand: Renegade Labs Pages: 114

Brand: SATA Pages: 294

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands