HP 8920A User Manual Download Page 92

Page: 92 / 658

S:\HP892XX\USRGUIDE\manual\acpscrn.fb

Chapter 4, Adjacent Channel Power Screen

Field Descriptions

AFGen1 Freq

This field sets the frequency for the first audio frequency sinewave generator.

AFGen1 To

This field sets two values:

•

The upper field determines whether the AFGen1 signal modulates the RF Generator or
is output through the AUDIO OUT connector.

•

The lower field sets the depth of modulation for FM and AM in kilohertz and amplitude
(including

Off

) for audio out. The AUDIO OUT level is always in volts rms.

Operating Considerations

This is a priority control field. Accessing the RX TEST or TX TEST screen
overrides any changes made to this field in other screens.

Carrier Ref

Use the carrier reference field to indicate whether the carrier (

Tune Freq

) being

measured should be unmodulated or modulated when making the ACP reference
measurement. (For more information, refer to

"How the Test Set Measures

Adjacent Channel Power (ACP)" on page 90

Operating Considerations
•

FM transmitters can be measured with the carrier modulated or unmodulated.

•

For AM transmitters, the carrier must be measured while unmodulated. AFGen1 and
the AUDIO OUT port must be used as the modulation source whenever

Unmod

selected.

Channel BW

Use the channel bandwidth field to specify the bandwidth of the carrier and
adjacent channels to be measured. (See

figure 14

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 8920A

Reviews:

Related manuals for 8920A

Brands by name

Popular brands

HP 8920A, User Manual

Search results

Summary of Contents for 8920A

Reviews:

Related manuals for 8920A

Brands by name

Popular brands