HP 8920A User Manual Download Page 187 | Manualshive

Page: 187 / 658

background image

187

Chapter 6, Call Processing Subsystem

Using the CALL DATA Screen

To View the Decoded Reverse Channel Words from a Mobile Station Page

There are two methods that can be used to view the decoded RVCC words from a
mobile station page:

•

View the decoded RVCC words from a page for a mobile station that has registered
with the Test Set

•

View the decoded RVCC words from a page for a mobile station that has not registered
with the Test Set

Viewing the Decoded Reverse Channel Words from a Page to a Mobile Station that
has Registered with the Test Set
1. If not already done, condition the Test Set.

See "Conditioning the Test Set for Call

Processing" on page 141

for further information.

2. If not already done, ensure that the Test Set is properly configured.

See "Configure the

Test Set" on page 142

for further information.

3. Connect the mobile station to the Test Set as shown in

Figure 17, "Connecting a

Mobile Station to the Test Set," on page 119

.

4. Turn on the mobile station.
5. If the CALL DATA screen is not displayed, select

CALL DATA

under the

To Screen

menu. The CALL DATA screen will be displayed.

6. Select the

Active

field. The

Active

annunciator will light when the control channel

is turned on.

7. Ensure that the mobile station has registered with the Test Set.

See "Register a Mobile

Station" on page 144

for information on how to register the mobile station.

8. Select the

Page

field. The

Page

annunciator will light while the Test Set pages the

mobile on the forward control channel. If the mobile station responds properly on the
reverse control channel, the message

RECC Return

will flash momentarily in the

upper right-hand corner of the CALL CONTROL screen. The

Access

annunciator

will then light while the Test Set sends the mobile station an alert order on the assigned
voice channel. The mobile station should ring.

9. Press the SEND key on the mobile station. The

Connect

annunciator will light if the

mobile station properly signals the Test Set when the SEND key is pressed. The mobile
station is now connected to the Test Set on the assigned voice channel.

10. Select the

Display Word

field. A list of reverse channel words appears in a

Choices:

menu. Select the desired word from the list of choices. The decoded

contents for each of the fields in the selected word will be displayed in the lower portion
of the display.

NOTE:

If a word is chosen which was not part of the decoded reverse channel’s message stream, all
the fields will be blank when it is displayed.

See "CALL DATA Screen Message Field Descriptions" on page 170

for a

description of each of the available reverse channel words.

«
...
185
186
187
188
189
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Brand: Raymarine Pages: 24

Brand: Hansen Pages: 72

Brand: Quadro mdb Pages: 4

Brand: AAT Pages: 16

Brand: AAT Pages: 40

Platinum Series

Brand: Dairy Tech Pages: 38

Brand: H&S Pages: 34

Brand: QAL Medical Pages: 42

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Raymarine Pages: 124

Brand: Raymarine Pages: 192

Brand: Varytec Pages: 5

Brand: Saab Pages: 98

Brand: Kaixin Pages: 89

Brand: Guyatone Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands