HP 8920A User Manual Download Page 521 | Manualshive

Page: 521 / 658

background image

521

Chapter 22, Tests Screen

Description of the Tests Subsystem

Tests Subsystem Screens

When you press the TESTS key, you access the main TESTS screen. The other
screens of the subsystem are accessed using the

CUSTOMIZE TEST PROCEDURE:

or

SET UP TEST SET:

lists at the bottom of this screen.

TESTS Subsystem Screens

•

Main Menu

is used to load a test procedure from a disk, RAM, ROM, or memory card.

It is also used to access the other screens in the Tests Subsystem.

•

Channel Information

is used to specify transmitter and receiver frequency infor-

mation for the radio being tested and to enter squelch and signaling information.

•

Test Parameters

is used to tell the Test Set the requirements of the test system for

testing your radio.

•

Order of Tests

is used to define a test sequence from a list of possible tests.

•

Pass/Fail Limits

is used to specify the upper and lower limits for each test point.

If a limit is violated during a test, an

F

appears next to the test value to indicate a failure.

•

Save/Delete Procedure

is used to save and delete test procedures.

•

Execution Conditions

is used to control which test results are output and where

the results are printed (CRT/printer). This screen also controls whether tests run contin-
uously or singly, and whether the test continues or stops after a failure is detected.

•

External Devices

is used to specify what types of external equipment are con-

nected to the Test Set and their addresses. It is also used to specify where to store test
result data.

•

Printer Setup

is used to control which test results are output and where the results

are printed. This screen is also used for basic formatting of the printout (lines per page
and form feeds). Printer port and printer model number are also chosen on this screen.

•

IBASIC Cntrl

is used to run IBASIC programs. This screen is also used as a stand-

alone IBASIC computer. See the Instrument BASIC Programmer’s Handbook for in-
formation about writing your own tests for the Test Set.

«
...
519
520
521
522
523
...
»

Summary of Contents for 8920A



















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 8920A

Brand: Ecco Pages: 4

Brand: JD Squared Pages: 15

Brand: DAPAudio Pages: 16

Brand: 3M Pages: 28

Brand: Jacobsen Pages: 6

Brand: Parker Pages: 54

Brand: Palazzetti Pages: 112

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Brand: Kellfri Pages: 12

Brand: Vapotherm Pages: 32

Brand: Vanguard Instruments Pages: 47

Brand: Yetter Pages: 24

Brand: TANNER Scientific Pages: 44

Brand: ABB Pages: 112

Brand: Major tech Pages: 12

Brand: Iwatsu Pages: 234

Brand: Rohm Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands