manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 6 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 6

Table of Contents

6

SCS Series Manual —

 P/N 15712:L  7/18/16

3.3.1: Inventory............................................................................................................................................36

3.4: Preliminary SCS-8⁄SCE-8 Design Considerations.......................................................................................36

3.4.1: Related Documentation .....................................................................................................................36
3.4.2: Fan and Damper Operation with the SCS-8 ......................................................................................37
3.4.3: Design Considerations .......................................................................................................................37
3.4.4: Selecting Fan and Damper Capabilities.............................................................................................37
3.4.5: Switch Group Type............................................................................................................................38
3.4.6: Switch Group Type Configuration ....................................................................................................38
3.4.7: Dipswitch Setting...............................................................................................................................40
3.4.8: EIA-485 Addressing ..........................................................................................................................40
3.4.9: Point Assignment...............................................................................................................................41

3.5: Cabinet and Chassis Mounting ....................................................................................................................42

ABS-4D Backbox .................................................................................................................................42
CAB-3, CAB-4 Cabinets ......................................................................................................................42
CHS-4L Chassis ...................................................................................................................................42
Custom Graphic Annunciator Cabinets ................................................................................................42

3.6: SCS-8⁄SCE-8 Installation.............................................................................................................................43

Labels....................................................................................................................................................43
ABS-4D Installation .............................................................................................................................43
CAB-3/CAB-4 Installation ...................................................................................................................43
EIA-485 ................................................................................................................................................43
Power Supply........................................................................................................................................46
Electrical Ratings..................................................................................................................................46
Programming and Testing the Smoke Control Station .........................................................................47

3.7: SCS-8L⁄SCE-8L Installation ........................................................................................................................47

Custom Graphic Annunciators .............................................................................................................47
CHS-4L Installation..............................................................................................................................47
Wiring the Switches..............................................................................................................................48
Wiring the LEDs or Lamps...................................................................................................................48
Installing Relay Modules......................................................................................................................50
EIA-485 ................................................................................................................................................51
Power Supply........................................................................................................................................52
Electrical Ratings..................................................................................................................................53
Calculating SCS-8L⁄SCE-8L Current Draw .........................................................................................53
Programming and Testing the Smoke Control Station .........................................................................54

3.8: Configuration ...............................................................................................................................................54

3.8.1: Firefighter's Smoke Control Station (FSCS) Mode ...........................................................................54

SCS Dipswitch Settings for FSCS Mode .............................................................................................54
Toggle Switch Operation for FSCS Mode............................................................................................61
Switch Group LEDs for FSCS Mode ...................................................................................................62
Dedicated System Operation ................................................................................................................63
Non-dedicated System Operation .........................................................................................................64

3.8.2: Heating, Ventilating & Air Conditioning (HVAC) Mode.................................................................65

SCS Dipswitch Settings for HVAC Mode ...........................................................................................66
Toggle Switch Operation for HVAC Mode..........................................................................................72
Switch Group LEDs for HVAC Mode .................................................................................................73

3.9: Programming................................................................................................................................................74

3.9.1: NFS2-3030, NFS-320, NFS2-640, and NCA-2.................................................................................74
3.9.2: NFS2-3030 and NCA-2/NFS2-640/NFS-320 Programming.............................................................75

Veri•Fire Tools Programming ..............................................................................................................77

3.9.3: NFS-320/NFS2-640 Programming (HVAC Mode, No CBE Lockout).............................................78

Veri•Fire Programming ........................................................................................................................79

3.9.4: INA Programming (Legacy Systems) ...............................................................................................80
3.9.5: AM2020/AFP1010 Programming (Legacy Systems)........................................................................80

EIA-485 Device Addressing.................................................................................................................81
Annunciator Point Programming..........................................................................................................82
Partial Point Programming ...................................................................................................................83

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments