manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 116 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 116

116

SCS Series Manual —

 P/N 15712:L  7/18/16

Ratings and Wiring Diagrams

Dedicated Smoke Control System Wiring Diagrams

Figure 5.8  Motorized Damper Control

 Dedicated System - FSCS Switch Group Type 4

Figure 5.8 depicts a motorized damper in a dedicated system with the capability of 

OPEN

 control and verification of the 

CLOSED

 state, switch 

group type 4. In the above configuration, the CON

ON⁄OP

CM is activated. The CON

ON⁄OP

CM controls a normally open contactor for the 

damper open power line and a normally closed contactor for the damper close power line. When the CON

ON⁄OP

CM is activated, the nor-

mally closed contactor is opened and the normally open contactor is closed, thus supplying power to open the damper. When the damper 
completely opens, the damper open limit switch is 

CLOSED

, indicating that the damper is in the 

OPEN

 position, and the damper closed limit 

switch is 

OPEN

. The VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed limit switch. In this case the VER

OFF⁄CL

MM is 

deactivated because the damper is 

CLOSED

.

Damper

Open

Power

Damper
Closed
Power

AC 

MOTOR

DAMPER

OPEN

1b listed

contactor

1a listed

contactor

Power Source

Listed 

24 VDC

Power Source

SLC Loop

ELR-47K

(use 3.9K listed ELR with FZM-1)

FCM-1 

CON

ON⁄OP

CM

(activated)

DM

O-d

f4

-fs-

2

.wmf

Power Return

VER

OFF⁄CL

MM

(activated

FMM-1

N/O

COM

Limit Switch
for closed 
position

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments