manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 113 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 113

SCS Series Manual —

 P/N 15712:L  7/18/16

113

Dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

5.3.2  Motorized Dampers

 

Figure 5.5  Motorized Damper Control

 Dedicated System - FSCS Switch Group Type 1

Figure 5.5 depicts a motorized damper in a dedicated system with the capability of 

CLOSED

 control and verification of the 

CLOSED

 state, 

switch group type 1. In the above configuration, the CON

OFF⁄CL

CM is activated. The CON

OFF⁄CL

CM controls a normally closed contact for 

the damper open power line and a normally open contact for the damper close power. When the CON

OFF⁄CL

CM is activated, the normally 

closed contact is opened and the normally open contact is closed, thus supplying power to close the damper. When the damper completely 
closes, the damper closed limit switch is 

CLOSED

, indicating that the damper is in the 

CLOSED

 position. The VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed limit switch. In this case the VER

OFF⁄CL

MM is activated because the damper is 

CLOSED

.

Power Source

1a listed

contactor

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power 

Return

Listed 

24 VDC

Power Source

FMM-1

FCM-1 

DM

O-

df1

-f

s

-2

.wm

f

SLC Loop

1b listed

contactor

CON

OFF/CL

CM

(activated)

VER

OFF/CL

MM

(deactivated)

Limit Switch
for closed 
position

Damper
Closed
Power

AC 

MOTOR

DAMPER

CLOSED

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments