manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 143 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 143

SCS Series Manual —

 P/N 15712:L  7/18/16

143

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.34  EP Damper Control, Non-dedicated System - FSCS Switch Group Type 3

Figure 5.34 depicts an EP damper in a non-dedicated system with the capability of 

CLOSED

 control and verification of the 

OPEN

 and 

CLOSED

 

state, switch group type 3. In the above configuration, the CON

OFF⁄CL

CM is activated. The CON

OFF⁄CL

CM controls a normally open contac-

tor for the pressure switch power line. When the CON

OFF⁄CL

CM is activated, the normally open contactor is closed. When the contactor 

closes, power is supplied to the pressure switch, which cuts the airflow to the damper and closes it. When the CON

OFF⁄CL

CM is deactivated, 

the EMS is free to control the damper. The EMS is currently being overridden by the CON

OFF⁄CL

CM.

When power is supplied to the pressure switch, the damper closes. When the damper completely closes, the damper closed limit switch is 

CLOSED

 and the damper open limit switch is 

OPEN

, indicating that the damper is in the 

CLOSED

 position. The VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper closed limit switch and the VER

ON⁄OP

MM monitors the 

CLOSED

 position of the damper open limit switch. In 

this case the VER

OFF⁄CL

MM is activated and the VER

ON⁄OP

MM is deactivated because the damper is 

CLOSED

.

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

CLOSED

Power Source

Listed 

24 VDC

Power Source

SLC Loop

FCM-1 

CON

OFF/CL

CM

(activated)

DE

P

-NF3

A

-f

s-2.wm

f

Power 

Return

VER

OFF⁄CL

MM

(deactivated)

N/O

COM

Limit Switch
for closed 
position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy

Management

System

1a listed
contact

N/O

COM

Limit Switch

for open 

position

VER

ON⁄OP

MM

(deactivated)

FMM-1

FMM-1

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V and 
type H modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments