manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 180 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 180

180

SCS Series Manual —

 P/N 15712:L  7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

Figure 5.72  EP Damper Control - HVAC Switch Group Type 6

Figure 5.72 depicts an EP damper in an HVAC system with the capability of 

CLOSED

 control and verification of the 

OPEN

 state, switch group 

type 6. In the above configuration, the CON

OFF⁄CL

CM is activated. The CON

OFF⁄CL

CM controls a normally open contactor for the pressure 

switch power line. When the CON

OFF⁄CL

CM is activated, the normally open contactor is closed. When the contactor closes, power is sup-

plied to the pressure switch, which cuts the airflow to the damper and closes it. When the CON

OFF⁄CL

CM is deactivated, the EMS is free to 

control the damper. The EMS is currently being overridden by the CON

OFF⁄CL

CM.

When power is supplied to the pressure switch, the damper closes. When the damper completely closes, the damper closed limit switch is 

CLOSED

, indicating that the damper is in the 

CLOSED

 position. The VER

ON⁄OP

MM monitors the 

CLOSED

 position of the damper open limit 

switch. In this case the VER

ON⁄OP

MM is deactivated because the damper is 

CLOSED

.

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

CLOSED

Power Source

Listed 

24 VDC

Power Source

SLC Loop

FCM-1 

CON

OFF/CL

CM

(activated)

De

p-

h6

-f

s-2

.w

m

f

Power 

Return

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

Energy

Management

System

1a listed
contactor

N/O

COM

Limit Switch

for open 

position

VER

ON⁄OP

MM

(deactivated)

FMM-1

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments