manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 197 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 197

SCS Series Manual —

 P/N 15712:L  7/18/16

197

The Null Control-By-Event

AM2020/AFP1010 Control-By-Event

A control module programmed with a Null Control-By-Event will not be activated unless it is included in the Control-By-Event of a soft-
ware zone or initiating device.

Example  -  Resetting 4-wire smoke detectors:

A control module is needed to reset power to 4-wire smoke detectors in an AM2020/AFP1010 system- 9This module must not be activated 
in response to an alarm condition. Rather, this module must only be activated during system reset. This can be accomplished by assigning the 
module a Null Control-By-Event and the Software Type ID PWRC (the control panel automatically resets modules with type PWRC upon 
system reset).

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments