manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 60 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 60

60

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

Configuration

28 

When used with an SCE, eight switch groups are 
available for group type 5 operation and eight are 
available for group type 1 operation in the format 
shown to the left. Type 5 switch groups require one 
control module and one monitor module. Type 5 switch 
groups can be used for fans or dampers. The control module is used for the ON control of the fan. 
The monitor module is used for the ON verification of the fan. Type 1 switch groups require one 
control module and one monitor module. Type 1 switch groups can be used for fans or dampers. The 
control module is used for OFF control of a fan and the monitor module is used for the OFF 
verification of the fan.

29 

When used with an SCE, eight switch groups are 
available for group type 5 operation and eight are 
available for group type 1 operation in the format 
shown to the left. Type 5 switch groups require one 
control module and one monitor module. Type 5 switch 
groups can be used for fans or dampers. The control module is used for the ON control of the fan. 
The monitor module is used for the ON verification of the fan. Type 1 switch groups require one 
control module and one monitor module. Type 1 switch groups can be used for fans or dampers. The 
control module is used for OFF control of a fan and the monitor module is used for the OFF 
verification of the fan.

30 

When used with an SCE, eight switch groups are 
available for group type 5 operation and eight are 
available for group type 2 operation in the format 
shown to the left. Type 5 switch groups require one 
control module and one monitor module. Type 5 switch 
groups can be used for fans or dampers. The control module is used for the ON control of the fan. 
The monitor module is used for the ON verification of the fan. Type 2 switch groups require one 
control module and one monitor module. Type 2 switch groups can be used for fans or dampers. The 
control module is used for OFF control of a fan and the monitor module is used for the ON verification 
of the fan.

31 

When used with an SCE, eight switch groups are 
available for group type 5 operation and eight are 
available for group type 2 operation in the format 
shown to the left. Type 5 switch groups require one 
control module and one monitor module. Type 5 switch 
groups can be used for fans or dampers. The control module is used for the ON control of the fan. 
The monitor module is used for the ON verification of the fan. Type 2 switch groups require one 
control module and one monitor module. Type 2 switch groups can be used for fans or dampers. The 
control module is used for OFF control of a fan and the monitor module is used for the ON verification 
of the fan.

32 

When used with an SCE, eight switch groups are 
available for group type 5 operation and eight are 
available for group type 3 operation in the format 
shown to the left. Type 5 switch groups require one 
control module and one monitor module. Type 5 switch 
groups can be used for fans or dampers. The control module is used for the ON control of the fan. 
The monitor module is used for the ON verification of the fan. Type 3 switch groups require one 
control module and two monitor modules. Type 3 switch groups are usually only used for dampers. 
The control module is used for CLOSED control of a damper, one monitor module is used for the 
OPEN verification of the damper and the other monitor module is used for the CLOSED verification 
of the damper.

*

See Table 3.4 for settings of dipswitches 7 and 8. 

Table 3.5  FSCS Mode Dipswitch Settings  (6 of 6) 

*

 

5

1

5

1

5

1

5

1

5

1

5

1

5

1

5

1

SCS-8

SCE-8

OFF
ON

5

5

5

5

1

1

1

1

1

1

1

1

5

5

5

5

SCS-8

SCE-8

OFF
ON

5

2

5

2

5

2

5

2

5

2

5

2

5

2

5

2

SCS-8

SCE-8

OFF
ON

5

5

5

5

2

2

2

2

2

2

2

2

5

5

5

5

SCS-8

SCE-8

OFF
ON

5

3

5

3

5

3

5

3

5

3

5

3

5

3

5

3

SCS-8

SCE-8

OFF
ON

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments