manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 40 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 40

40

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

Preliminary SCS-8⁄SCE-8 Design Considerations

3.4.7  Dipswitch Setting

The eight dipswitches are used to control the function of the SCS⁄SCE. The dipswitches perform the functions as listed in Table 3.4, where: 
switches 1-5 control the combinations of switch group types; switch 6 controls whether the SCS⁄SCE operates in the FSCS or the HVAC 
mode; switch 7 selects Dedicated or Non-dedicated System operation when in the FSCS mode or enables/disables the Control-By-Event 
lockout when manual operation is initiated in the HVAC mode; and switch 8 installs or removes the end-of-line termination resistor. 

3.4.8  EIA-485 Addressing

The SCS-8 communicates with the FACP on the EIA-485 data line. 
Each SCS-8 requires a unique address so that the FACP can properly 
route data. There are 32 valid addresses in an FACP EIA-485 circuit 
in ACS mode, numbered 1-32, and each address provides the SCS 
with 64 points of monitor and control capability. Each SCS-8⁄SCE-8 
uses one EIA-485 protocol address and its respective point capacity 
(64 points). The first 32 points are used for the SCS-8; the second 32 
are used for the SCE-8.

Addressing the SCS-8 is accomplished by using the two rotary deci-
mal switches mounted on the SCS-8. The decimal switches must be 
set to any of the available valid addresses (1-32) of the FACP. Each SCS-8 must be set to an address that is different than all other EIA-485 
driven devices (annunciators, other SCS-8s, etc.). 

The rotary switches are set by using a screwdriver to position the indicating mark on the rotary portion of the switch next to the desired digit. 
For example, to set address 14, the 'TENS' switch is set to 1 and the 'ONES' switch is set to 4.

Table 3.4  SCS Dipswitch Mode Configurations

SWITCH 

NUMBER

DESCRIPTION

FUNCTION

SWITCH LOCATION & POSITION

1 to 5

Selects which combination of control/monitor 
modules are assigned to each SCS-8⁄SCE-8 
toggle switch group

See Table 3.5 on page 55 for 
FSCS Mode.
See Table 3.10 on page 67 for 
HVAC Mode.

6*

Selects FSCS Mode or HVAC Mode for all 16 
SCS-8⁄SCE-8 toggle switch groups

ON = FSCS Mode 
OFF = HVAC Mode 

7*

For FSCS Mode, selects Dedicated or Non-
dedicated System for all 16 SCS-8⁄SCE-8 
toggle switch groups

ON = Dedicated 
OFF = Non-dedicated

For HVAC Mode, enables/disables Control-
By-Event lockout when manual operation is 
initiated at the SCS-8⁄SCE-8

ON = Enabled 
OFF = Disabled

8

Installs or removes the built-in 120 ohm EIA-
485 end-of-line termination resistor (see 
Figure 3.14)

ON = Installed
OFF = Removed 

*Must be set “OFF” for INA, or when the SCS module is directly connected to the EIA-485 bus of an NFS-320, NFS2-640, or NFS-640 

FACP.

Switch set to 
"OFF" position

Switch set to 
"ON" position

Switch Locations

Figure 3.4  SCS Address Switches

ONES

TENS 

SC

S-

SW

IT.w

m

f

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments