manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 152 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 152

152

SCS Series Manual —

 P/N 15712:L  7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

Figure 5.43  Fan Control - HVAC Switch Group Type 4

Figure 5.43 depicts a fan in an HVAC system with the capability of 

OFF

 control, switch group type 4. In the above configuration, the 

CON

OFF⁄CL

CM is deactivated. The CON

OFF⁄CL

CM controls a normally closed contactor which switches power to the fan (the contactor is 

used when the power being switched is greater than 24 volts). When the CON

OFF⁄CL

CM is deactivated, the contactor is closed, thus allowing 

the EMS to freely control the fan. In this case the EMS is 

OFF

, so no power is being supplied to the fan. When no power is supplied to the fan, 

the fan is 

OFF

. When the CON

OFF⁄CL

CM is activated, the normally closed contactor opens, thus cutting any power to the fan that was being 

supplied by the EMS.

Power Source

1b listed

contact

Service 
Disconnect 
Switch

Power Return

Listed 

24 VDC

Power Source

FCM-1 

CON

OFF/CL

CM

(deactivated)

fa

n-

h4

-f

s-2

.w

m

f

SLC Loop

FAN OFF

Listed contact

for Energy

Management

System

Energy Management System

Listed 
24 VDC
Power Source

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V and 
type H modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments