manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 129 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 129

SCS Series Manual —

 P/N 15712:L  7/18/16

129

Non-dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.20  Fan Control, Non-dedicated System - FSCS Switch Group Type 5

Figure 5.20 depicts a fan in a non-dedicated system with the capability of 

ON

 control and verification of the 

ON

 state, switch group type 5. In 

the above configuration, the CON

ON⁄OP

CM is deactivated. The CON

ON⁄OP

CM is wired in parallel with the EMS; when wired in parallel with 

the EMS the CM must be a relay module. When the CON

ON⁄OP

CM is deactivated, the EMS is free to control the fan. In this case the EMS is 

OFF

, so no power is being supplied to the fan. When no power is supplied to the fan, the fan is 

OFF

 and the sail switch is 

CLOSED

, indicating 

no airflow in the duct. The VER

ON⁄OP

MM monitors the 

OPEN

 position of the sail switch, which would indicate when the fan is 

ON

. In this 

case the VER

ON⁄OP

MM is deactivated because the fan is 

OFF

 due to the EMS. When the CON

ON⁄OP

CM is activated, the CON

ON⁄OP

CM over-

rides whatever state the EMS is in and closes the normally open contactor, thus supplying power to the fan and turning it 

ON

.

Switch group type 6 is for a fan that would require the capability of 

ON

 control and verification of both the 

ON

 and 

OFF

 states. Since it is pos-

sible to determine this information from both switch group type 4 or switch group type 5, switch group type 6 would only be necessary for 
redundancy in verifying the state of the fan. For example, if switch group type 4 is used instead of switch group type 6, the 

OFF

 state of the 

fan would be verified when the monitor module is activated and the 

ON

 state of the fan would be verified when the monitor module is deac-

tivated. Utilizing switch group type 4 or 5 also saves the use of an additional monitor module. Switch group type 6 would use two monitor 
modules to provide the same verification as types 4 or 5. 

FRM-1

COM

N/O.

Power Source

1a listed

contactor

Service

Disconnect

Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed 

Sail 

Switch

N/O

COM

N/C

Power Return

VER

ON/OP

MM

(deactivated)

fa

n-

nf

5

-f

s

-2

.wm

f

SLC Loop

FAN OFF

Energy 
Management 
System

Listed 

24 VDC

Power Source

FMM-1

CON

ON/OP

CM

(deactivated)

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments