manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 164 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 164

164

SCS Series Manual —

 P/N 15712:L  7/18/16

Ratings and Wiring Diagrams

HVAC Wiring Diagrams

Figure 5.55  Motorized Damper Control - HVAC Switch Group Type 4

Figure 5.55 depicts a motorized damper in an HVAC system with the capability of 

CLOSED

 control, switch group type 4. In the above config-

uration, the CON

OFF⁄CL

CM is deactivated. The CON

OFF⁄CL

CM controls two contactors: a normally closed contactor for the damper open 

power line, and a dual normally open/normally closed contactor for the damper close power. When the CON

OFF⁄CL

CM is activated, the nor-

mally closed contactor is opened (cutting any power supplied by the EMS to the damper open power line), the normally closed portion of the 
dual contactor is opened (cutting any power supplied by the EMS to the damper closed power line), and the normally open portion of the 
dual contactor is closed, thus supplying power to close the damper. When the CON

OFF⁄CL

CM is deactivated, the EMS is free to control the 

damper. The EMS is currently supplying power to the damper closed power line. When power is supplied to the damper closed power line, 
the damper closes.

Power Source

Damper

Open

Power

Power Return

Listed 

24 VDC

Power Source

D

M

O-

h4

a-

fs-

2

.w

m

f

SLC Loop

Damper
Closed
Power

AC 

MOTOR

DAMPER

CLOSED

FCM-1 

CON

OFF/CL

CM

(deactivated)

Energy 

Management

System

1b listed contact

1a, 1b

listed

contactor

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments