manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 109 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 109

SCS Series Manual —

 P/N 15712:L  7/18/16

109

Dedicated Smoke Control System Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.2  Fan Control, Dedicated System - FSCS Switch Group Type 2

Figure 5.2 depicts a fan in a dedicated system with the capability of 

OFF

 control and verification of the 

ON

 state, switch group type 2. In the 

above configuration, the CON

OFF⁄CL

CM is deactivated. The CON

OFF⁄CL

CM controls a normally closed contact which switches power to the 

fan (the contact is used when the power being switched is greater than 24 volts). When the CON

OFF⁄CL

CM is deactivated, the contact is 

closed, thus supplying power to the fan. When power is supplied to the fan, the fan is 

ON

 and the sail switch is 

OPEN

, indicating airflow in the 

duct. The VER

ON⁄OP

MM monitors the 

OPEN

 position of the sail switch, which would indicate when the fan is 

ON

. In this case the 

VER

ON⁄OP

MM is activated because the fan is 

ON

 and the sail switch is 

OPEN

.

Switch group type 3 is for a fan that would require the capability of 

OFF

 control and verification of both the 

ON

 and 

OFF

 states. Since it is pos-

sible to determine this information from either switch group type 1 or switch group type 2, switch group type 3 would only be necessary for 
redundancy in verifying the state of the fan. For example, if switch group type 1 is used instead of switch group type 3, the 

OFF

 state of the 

fan would be verified when the monitor module is activated and the 

ON

 state of the fan would be verified when the monitor module is deac-

tivated. Utilizing switch group types 1 or 2 also saves the use of an additional monitor module. Switch group type 3 would use two monitor 
modules to provide the same verification as types 1 or 2. 

Power Source

1b listed
contactor

Service 
Disconnect 
Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed 

Sail 

Switch

N/O

COM

N/C

Power Return

Listed 

24 VDC

Power 

Source

FMM-1

FCM-1 

CON

OFF/CL

CM

(deactivated)

F

A

N-

D

f2

-f

s

-2

.w

mf

SLC Loop

FAN ON

VER

ON/OP

MM

(activated)

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments