manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 56 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 56

56

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

Configuration

5 

When used with an SCE, eight switch groups are 
available for group type 8 operation and eight are 
available for group type 1 operation in the format 
shown to the left. Type 8 switch groups require two 
control modules and one monitor module. Type 8 
switch groups can be used for fans or dampers. One control module is used for the ON control of the 
fan, the other control module is used for the OFF control. The monitor module is used for the ON 
verification of the fan. Type 1 switch groups require one control module and one monitor module. 
Type 1 switch groups can be used for fans or dampers. The control module is used for OFF control of 
a fan and the monitor module is used for the OFF verification of the fan.

6 

When used with an SCE, all 16 switch groups are 
available for group type 1 operation. Type 1 switch 
groups require one control module and one monitor 
module. Type 1 switch groups can be used for fans or 
dampers. The control module is used for OFF control 
of a fan and the monitor module is used for the OFF verification of the fan.

7 

When used with an SCE, all 16 switch groups are 
available for group type 2 operation. Type 2 switch 
groups require one control module and one monitor 
module. Type 2 switch groups can be used for fans or 
dampers. The control module is used for OFF control 
of a fan and the monitor module is used for the ON verification of the fan.

8 

When used with an SCE, all 16 switch groups are 
available for group type 3 operation. Type 3 switch 
groups require one control module and two monitor 
modules. Type 3 switch groups are usually only used 
for dampers. The control module is used for CLOSED 
control of a damper, one monitor module is used for the OPEN verification of the damper and the 
other monitor module is used for the CLOSED verification of the damper.

9 

When used with an SCE, eight switch groups are 
available for group type 8 operation and eight are 
available for group type 2 operation in the format 
shown to the left. Type 8 switch groups require two 
control modules and one monitor module. Type 8 
switch groups can be used for fans or dampers. One control module is used for the ON control of the 
fan, the other control module is used for the OFF control. The monitor module is used for the ON 
verification of the fan. Type 2 switch groups require one control module and one monitor module. 
Type 2 switch groups can be used for fans or dampers. The control module is used for OFF control of 
a fan and the monitor module is used for the ON verification of the fan.

10 

When used with an SCE, all 16 switch groups are 
available for group type 4 operation. Type 4 switch 
groups require one control module and one monitor 
module. Type 4 switch groups can be used for fans or 
dampers. The control module is used for ON control of 
a fan and the monitor module is used for the OFF verification of the fan.

Table 3.5  FSCS Mode Dipswitch Settings  (2 of 6) 

*

 

8

1

1

8

8

1

1

8

8

1

1

8

8

1

1

8

SCS-8

SCE-8

OFF
ON

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

SCS-8

SCE-8

OFF
ON

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

SCS-8

SCE-8

OFF
ON

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

3

SCS-8

SCE-8

OFF
ON

8

2

2

8

8

2

2

8

8

2

2

8

8

2

2

8

SCS-8

SCE-8

OFF
ON

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

SCS-8

SCE-8

OFF
ON

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments