manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 196 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 196

196

SCS Series Manual —

 P/N 15712:L  7/18/16

AM2020/AFP1010 Control-By-Event

The Null Control-By-Event

By using two reverse-activating zones, the equation with 15 bytes is broken into two smaller Equations and the CBE for the control module 
uses the two reverse-activating zones as its operands.

CBE Equation for 

Z238

:

  OR(Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8)  

=  10 Bytes

CBE Equation for 

Z239

:

  OR(Z9 Z10 Z11 Z12 Z13 Z14) 

= 8 Bytes

CBE Equation for 

L1M1

:

  OR(Z238 Z239)

=  4 Bytes

A.5  The Null Control-By-Event

The simplest type of Control-By-Event is the Null, which means empty. 

For initiating devices, the Null is denoted by entering  ( )  as the Control-By-Event.

In response to an alarm on a device programmed with a Null Control-By-Event, the AM2020/AFP1010 will do the following:

•

Initiate a System Alarm condition (Alarm LED flashes, piezo chirps and the Form-C alarm contacts on the CPU will be activated).

•

Activate no control modules or software zones (no notification appliances will sound and no output relays will be activated due to the 
fact that there are no entries in the Control-By-Event for this initiating device).

For Output Devices, the Null is denoted by entering  OR( )  or  ( )

Programming Shortcut: Entering  (  is equivalent to entering  OR(

Z4

Z5

Z2

Z7

Z8

Z13

Z10

Z11

Z3

Z6

Z14

Z1

Z9

Z12

Z239

RZON

Z240

RZON

L1M1

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments