manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 165 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 165

SCS Series Manual —

 P/N 15712:L  7/18/16

165

HVAC Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.56  Motorized Damper Control - HVAC Switch Group Type 5

Figure 5.56 depicts a motorized damper in an HVAC system with the capability of 

CLOSED

 control and verification of the 

CLOSED

 state, 

switch group type 5. In the above configuration, the CON

OFF⁄CL

CM is deactivated. The CON

OFF⁄CL

CM controls two contactors: a normally 

closed contactor for the damper open power line, and a dual normally open/normally closed contactor for the damper close power. When the 
CON

OFF⁄CL

CM is activated, the normally closed contactor is opened (cutting any power supplied by the EMS to the damper open power 

line), the normally closed portion of the dual contactor is opened (cutting any power supplied by the EMS to the damper closed power line), 
and the normally open portion of the dual contactor is closed, thus supplying power to close the damper. When the CON

OFF⁄CL

CM is deacti-

vated, the EMS is free to control the damper. The EMS is currently supplying power to the damper closed power line.

When power is supplied to the damper closed power line, the damper closes. When the damper completely closes, the damper closed limit 
switch is 

CLOSED

, indicating that the damper is in the 

CLOSED

 position. The VER

OFF⁄CL

MM monitors the 

CLOSED

 position of the damper 

closed limit switch. In this case the VER

OFF⁄CL

MM is activated because the damper is 

CLOSED

.

Power Source

Damper

Open

Power

ELR-47K

(use 3.9K listed ELR with FZM-1)

N/O

COM

Power Return

Listed 

24 VDC

Power Source

FMM-1

D

M

O-

h5

a-

fs

-2

.w

mf

SLC Loop

VER

OFF/CL

MM

(activated)

Limit Switch
for closed 
position

Damper
Closed
Power

AC 

MOTOR

DAMPER

CLOSED

FCM-1 

CON

OFF/CL

CM

(deactivated)

Energy 

Management

System

1b listed contact

1a, 1b

listed

contact

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains 
wiring conversion 
charts for type V 
and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments