manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 151 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 151

SCS Series Manual —

 P/N 15712:L  7/18/16

151

HVAC Wiring Diagrams

Ratings and Wiring Diagrams

Figure 5.42  Fan Control - HVAC Switch Group Type 2

Figure 5.42 depicts a fan in an HVAC system with the capability of verifying the 

ON

 state, switch group type 2. In the above configuration, 

the EMS is deactivated. The EMS controls a normally closed contactor which switches power to the fan. When no power is supplied to the 
fan, the fan is 

OFF

 and the sail switch is 

CLOSED

, indicating no airflow in the duct. The VER

ON⁄OP

MM monitors the 

OPEN

 position of the sail 

switch, which would indicate when the fan is 

ON

. In this case the VER

ON⁄OP

MM is deactivated because the fan is 

OFF

 and the sail switch is 

CLOSED

.

Switch group type 3 is for a fan that would require the capability of verifying both the 

ON

 and 

OFF

 states. Since it is possible to determine this 

information from either switch group type 1 or switch group type 2, switch group type 3 would only be necessary for redundancy in verifying 
the state of the fan. For example, if switch group type 1 is used instead of switch group type 3, the 

OFF

 state of the fan would be verified 

when the MM is activated and the 

ON

 state of the fan would be verified when the monitor module is deactivated. Utilizing switch group types 

1 or 2 also saves the use of an additional monitor module. Switch group type 3 would use two monitor modules to provide the same verifica-
tion as types 1 or 2. 

Power Source

Service 
Disconnect 
Switch

ELR-47K

(use 3.9K listed ELR with FZM-1)

Listed 

Sail 

Switch

N/O

COM

N/C

Power Return

VER

ON/OP

MM

(deactivated)

fan-

h

2

-f

s-

2.w

m

f

SLC Loop

FAN OFF

Listed contact for 
Energy 
Management 
System

Energy Management System

Listed 
24 VDC
Power Source

FMM-1

*If the SLC device 
does not match the 
one in this figure, 
refer to the SLC 
manual appendix, 
which contains wiring 
conversion charts for 
type V and type H 
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments