Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 122

Page: 122 / 210

122

SCS Series Manual —

P/N 15712:L 7/18/16

Ratings and Wiring Diagrams

Dedicated Smoke Control System Wiring Diagrams

Figure 5.13 EP Damper Control, Dedicated System - FSCS Switch Group Type 3

Figure 5.13 depicts an EP damper in a dedicated system with the capability of control and verification of the

OPEN

and

CLOSED

state, switch

group type 3. In the above configuration, the CON

OFF⁄CL

CM is activated. The CON

OFF⁄CL

CM controls a normally open contactor for the

pressure switch power. When the CON

OFF⁄CL

CM is activated, the normally open contactor is closed, thus supplying power to close the

damper. When the damper completely closes, the damper closed limit switch is closed, indicating that the damper is in the

CLOSED

position.

(When the damper is in the open position, the damper open limit switch is closed.) The VER

OFF⁄CL

MM monitors when the damper closed

limit switch is

CLOSED

. In this case the VER

OFF⁄CL

MM is activated and the VER

ON⁄OP

MM is deactivated because the damper is

CLOSED

Airflow

PRESSURE

SWITCH

SMOKE

DAMPER

CLOSED

1a listed

contactor

Listed

24 VDC

Power Source

SLC Loop

FCM-1

CON

OFF/CL

(activated)

EP-

-f

Power

Return

FMM-1

VER

OFF⁄CL

(activated)

FMM-1

N/O

COM

Limit Switch
for closed
position

ELR-47K

(use 3.9K listed ELR with FZM-1)

Pneumatic

Tubing

N/O

COM

Limit Switch

for open

position

VER

ON⁄OP

(deactivated)

Power Source

*If the SLC device
does not match the
one in this figure, refer
to the SLC manual
appendix, which
contains wiring
conversion charts for
type V and type H
modules.

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Search results

Summary of Contents for NOTIFIER SCS Series

Reviews:

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 122 / 210

Search results

Summary of Contents for NOTIFIER SCS Series

Reviews: