Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 49

Page: 49 / 210

SCS Series Manual —

P/N 15712:L 7/18/16

SCS-8L⁄SCE-8L Installation

The SCS⁄SCE

The maximum output current for each LED or Lamp is 50 mA if powered by 24 VDC or 20 mA if powered by 5 VDC.

NOTE:

All LEDs must be located in the same room as the modules.

Trouble Lamps (groups 1-8 f

8L, groups 9-16 for SCE

Trouble Lamp group 1 or 9

Trouble Lamp group 2 or 10

Trouble Lamp group 3 or 11

Trouble Lamp group 4 or 12

Trouble Lamp group 5 or 13

Trouble Lamp group 6 or 14

Trouble Lamp group 7 or 15

Trouble Lamp group 8 or 16

ON/OFF Lamps

(groups 1-4 for SCS-8L,

groups 9-12 for SCE-8L)

OFF Lamp group 4 or 12

ON Lamp group 4 or 12

OFF Lamp group 3 or 11

ON Lamp group 3 or 11

OFF Lamp group 2 or 10

ON Lamp group 2 or 10

OFF Lamp group 1 or 9

ON Lamp group 1 or 9

ON/OFF Lamps

(groups 5-8 for SCS-8L,

groups 13-16 for SCE-8L)

ON Lamp group 5 or 13

OFF Lamp group 5 or 13

ON Lamp group 6 or 14

OFF Lamp group 6 or 14

ON Lamp group 7 or 15

OFF Lamp group 7 or 15

ON Lamp group 8 or 16

OFF Lamp group 8 or 16

Figure 3.20 Lamp Wiring for SCS-8L⁄SCE-8L

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Search results

Summary of Contents for NOTIFIER SCS Series

Reviews:

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 49 / 210

Search results

Summary of Contents for NOTIFIER SCS Series

Reviews: