manualshive.com logo in svg

Honeywell NOTIFIER SCS Series, Operation And Installation Manual, Page: 52 / 210

Share
Download
Honeywell NOTIFIER SCS Series Operation And Installation Manual Download Page 52

52

SCS Series Manual —

 P/N 15712:L  7/18/16

The SCS⁄SCE

SCS-8L⁄SCE-8L Installation

When the EIA-485 shield is not in conduit: Terminate the shield at the outside of the FACP backbox (ground). Do not allow the shield to 
enter or even touch the cabinet. Between Smoke Control Stations, wire-nut multiple shields together outside of the respective enclosures.  

Power Supply

Power for the Smoke Control Station is provided via a separate power loop from the control panel which is inherently supervised (loss of 
power also results in a communication failure at the control panel). If the SCS-8L is powered remotely, it must be powered by a Power Lim-
ited power supply listed for fire protective signaling and there must be a common connection between the negative battery terminals of each 
supply. Use of the RPT-485 isolator/repeater in the control panel to isolate the EIA-485 line eliminates the need for the common connection 
between power supplies.

Enclosure

SCS-8L 

Terminal Block

Figure 3.25  Terminating the Shield

NOTE:

All enclosures, including the FACP backbox, must be connected to earth ground! Never use the shield for grounding purposes. 

Terminate the EIA-485 shield at the Fire Alarm Control Panel only.

EIA-485 In (–)

EIA-485 Out (–)
EIA-485 Out (+)

EIA-485 In(+)

Not Used
Not Used

Common In (–)

Common Out (–)

Power In (+24 VDC)

Power Out (+24 VDC)

Earth Ground

TB2

TB1

Figure 3.26  SCS-8L Terminal Blocks

Summary of Contents for NOTIFIER SCS Series



















































































































































































































Reviews:

No comments