Honeywell Chadwick-Helmuth 8500C Maintenance Manual Download Page 25

Page: 25 / 186

Chapter 2

8500C/8500C+ System Maintenance Manual

2-1

8500C/C+ Handling And Installation

Section 2.1 Preparation For Use .........................................................................................2-1

Section 2.2 Repacking..........................................................................................................2-4

Section 2.3 Storage ..............................................................................................................2-4

2.1 Preparation For Use

2.1.1 Unpacking

Open shipping container and remove carrying case and accessories.

Open carrying case and remove major components, cables, and accessories.

Check contents of shipping container and carrying case against enclosed Packing List.

Carefully unwrap each major component, cable, and accessory.

After transit, ensure that printer paper roll is tightly wound again by removing and

reloading as instructed in sections 2.1.4 and 2.1.5.

NOTE: In the event of damaged or missing equipment report all details to Chadwick-
Helmuth.

2.1.2 Cable Interconnections

Connect cable 10811-12 to POWER/SIGNAL IN connector on 8500C/C+ and OUTPUT/
POWER to 8500C/C+ connector on 8520C.

Ensure system is connected to a 28 VDC power source only. Serious damage to equipment
and/or personnel injury could result if connected to any AC power source.

Connect cable 10813-12 from DC POWER connector on 8520C to a 28 VDC power
supply.

If necessary, adjust contrast knob to read display (Figure 2-1).

NOTE: It is best practice to use minimum backlight.

WARNING

Summary of Contents for Chadwick-Helmuth 8500C



























































































































































































Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands

Honeywell Chadwick-Helmuth 8500C, Maintenance Manual

Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands