Honeywell Chadwick-Helmuth 8500C Maintenance Manual Download Page 60 | Manualshive

Page: 60 / 186

background image

5-16

Chadwick-Helmuth A Business Unit of Honeywell International, Inc.

Chapter 5

- Maintenance And Repair

Window:

Flat top

Source:

Off

Input:

DC Coupling, Auto range on

Units:

X: Hz, Y: Volt

Vertical Scale: Linear

b.

Reconnect Velocimeter coax cable to cable 8998.

c.

Set up signal generator as follows: For channel connected to Velocimeter input, set to

Frequency = 1722 +/- 1 Hz, Waveform = Sine wave, Amplitude = 19.0 mV pk. Monitor
signal generator output with spectrum analyzer with marker at 1722 Hz. Adjust signal
generator output channel connected to Velocimeter input until amplitude is 13.44 +/- 0.05
mV RMS.

d.

Press

SETUP

key.

e.

Key in

500 (Hz)

with numeric keys in

MAXIMUM FREQUENCY

field.

f.

Press

ENTER

key.

g.

Wait 10 seconds.

h.

Press

START

key.

i.

Verify that no signal aliasing remains on display above 0.005 IPS.

5.5.1.5.2 10 kHz Anti-Aliasing

a.

Set up spectrum analyzer to view a 13.44 mVrms, 15,600 Hz signal.

Use the following analyzer settings:

Frequency:

Baseband, Start: 0 Hz, Stop: 20000 Hz

Trigger:

Free run

Average:

Off

Window:

Flat top

Source:

Off

Input:

DC Coupling, Auto range on

Units:

X: Hz, Y: Volt

Vertical Scale: Linear

b.

Turn on signal generator and set up as follows: For channel connected to Velocimeter
input, set to Frequency = 15,600 +/- 10 Hz. Waveform = Sine wave, Amplitude = 19.0 mV
pk. Monitor signal generator output with spectrum analyzer with marker at 15,600 Hz.
Adjust signal generator output channel connected to Velocimeter input until amplitude is
13.44 +/- 0.05 mV RMS.

c.

Press

SETUP

key.

d.

Key in

10000 (Hz)

with numeric keys in

MAXIMUM FREQUENCY

field.

e.

Press

ENTER

key.

f.

Wait 10 seconds.

«
...
58
59
60
61
62
...
»

Summary of Contents for Chadwick-Helmuth 8500C



























































































































































































Reviews:

No comments

Related manuals for Chadwick-Helmuth 8500C

Brand: ABB Pages: 8

Brand: Panasonic Pages: 72

KW9M Eco-Power Meter

Brand: Panasonic Pages: 2

Brand: Quantel Pages: 2

Brand: Halcyon Pages: 36

Brand: NanoEnTek Pages: 4

Brand: OBDPROG Pages: 8

Brand: Flytec Pages: 2

Brand: Barksdale Pages: 2

Brand: Keeler Pages: 54

Solicap M FTI55

Brand: Endress+Hauser Pages: 92

Brand: SICK Pages: 68

Brand: A&D Pages: 2

Brand: JensPrima Pages: 20

SoundExpert LxT

Brand: Larson Davis Pages: 307

Brand: Velleman-Kit Pages: 9

DistanceMaster Compact

Brand: LaserLiner Pages: 14

Brand: inbody Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands