Honeywell Chadwick-Helmuth 8500C Maintenance Manual Download Page 164

Page: 164 / 186

D-6

Chadwick-Helmuth A Business Unit of Honeywell International, Inc.

Appendix D -

8520CS Signal Selector

Press

ENTER

soft key.

Wait 10 seconds.

Press

START

key.

Verify that display indicates (example in Figure D-3):

1800 +2 RMP

0.8+0.08 IPS

275+10°

Press

STOP

key.

Press

SETUP

key.

Select

INPUT

field with arrow keys.

Key in

with numeric key.

Press

ENTER

soft key.

Wait 10 seconds.

Press

START

key.

Verify that display indicates (example in Figure D-3):

1800+2 RPM

0.8+0.08 IPS

275+10°

aa.

Press

STOP

key.

bb.

Move 11210 cables to next Velocimeter Channel positions and cable 10808 to magnetic
pickup channel position marked in Table D-2.

cc.

Press

SETUP

on 8500C/C+.

dd.

Select

PICKUP

field with arrow keys.

ee.

Press

CHANGE

soft key to select pickup shown in Table D-2.

ff.

Press

INPUT

field with arrow keys.

gg.

Key in channel number with numeric key.

hh.

Press

ENTER

soft key.

ii.

Wait 10 seconds.

Table D-2. Velocimeter and Magnetic Pickup Balance Test Channel

Combinations

Velocimeter Channels

Magnetic Pickup Channel

1, 2, 4, 5

7, 8, 10, 11

Summary of Contents for Chadwick-Helmuth 8500C



























































































































































































Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands

Honeywell Chadwick-Helmuth 8500C, Maintenance Manual

Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands