Honeywell Chadwick-Helmuth 8500C Maintenance Manual Download Page 15

Page: 15 / 186

System Physical Description

8500C/8500C+ System Maintenance Manual

1-3

The 8500C/C+ printer/disk drive assembly is composed of the following items:

•

Printer assembly: prints data and solutions on paper.

•

Printer board: interfaces with the printer.

•

Disk drive assembly: uploads software from the diskette to the balancer/analyzer assembly.

•

Distribution board: interfaces with the disk drive assembly and balancer/analyzer assembly.

•

Power supply: generates operating voltages for the printed circuit boards in the balancer/
analyzer assembly and printer/disk drive assembly.

•

Harness assembly: interconnects the printed circuit boards, printer assembly, and disk drive
assembly.

Figure 1-1. 8500C/C+ Balance/Analyzer

Summary of Contents for Chadwick-Helmuth 8500C



























































































































































































Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands

Honeywell Chadwick-Helmuth 8500C, Maintenance Manual

Search results

Summary of Contents for Chadwick-Helmuth 8500C

Reviews:

Related manuals for Chadwick-Helmuth 8500C

Brands by name

Popular brands